Tie Strap

1. Turn OFF the engine for 30 seconds before proceeding to purge the fuel pressure from the complete fuel system.
2. Front Wheelhouse Liner-Left Side»Remove—Front Wheelhouse Liner Replacement
3. Disconnect all wiring harness retainers from the fuel feed and fuel return pipe.



4. Fuel Feed Pipe(1)»Disconnect—Metal Collar Quick Connect Fitting Service
5. Fuel Return Pipe(2)»Disconnect—Metal Collar Quick Connect Fitting Service
6. Remove underbody panels as necessary.Underbody Panel Component Locator



7. {with F47} Unclip the 2 air line retainers (1) and reposition the air line (2).



8. {with F47} Remove the chassis wire harness clip (1) from the automatic level control air supply reservoir.



9. {with F47} Remove the 3 automatic level control air compressor bolts (1).
10. {with F47} Reposition and support the automatic level control air supply reservoir (2) out of the way of the transmission support crossmember.



11. { If equipped } Remove the 3 wiring harness retainers (1) from the transmission support crossmember, and reposition the wiring harness (2) as necessary.
12. Support the transmission with a suitable jack.



13. Transmission Mount Nut(1)»Remove[2X]
14. Transmission Support Crossmember Nut(2)»Remove[4x]
15. Transmission Support Crossmember Bolt(3)»Remove[4x]



16. Transmission Support Crossmember(1)»Remove
17. Lower the transmission to gain access to the top and sides of the transmission.



18. Mark a reference point between the front axle propeller shaft (1) and the front differential drive pinion gear yoke.
19. Front Axle Propeller Shaft Bolt(2)»Remove[6x]
20. Front Axle Propeller Shaft Washer(3)»Remove[3x]
21. Front Axle Propeller Shaft(1)»Reposition away



22. Hose Clamp(1)»Disengage[2x]—Hose Clamp Replacement Guidelines - Spring Type
23. Fuel Cooler Coolant Cooler Inlet Hose (2)»Remove and position aside[2x]



24. Fuel Feed and Return Front Hose Bracket Nut(1)»Remove
25. Fuel Feed and Return Pipe(2)»Remove



26. Fuel Return Pipe(1)»Disconnect—Metal Collar Quick Connect Fitting Service
27. Tie Strap (2)»Remove and DISCARD
28. Fuel Feed and Return Pipe(4)@Retainer(3)»Disengage
29. { If equipped } Remove the transfer case vent hose retainers.



30. Fuel Feed and Return Pipe(1)»Disconnect—Plastic Collar Quick Connect Fitting Service
31. Fuel Feed and Return Pipe(1)@Retainer(2)»Disengage
32. Fuel Feed and Return Pipe(1)»Remove



33. Fuel Return Pipe(1)@Retainer(2)»Disengage[2x]
34. Fuel Return Pipe(1)»Remove

1. Fuel Return Pipe(1)»Install
2. Fuel Return Pipe(1)@Retainer(2)»Engage[2x]



3. Fuel Feed and Return Pipe(1)»Install
4. Fuel Feed and Return Pipe(1)@Retainer(2)»Engage
5. Fuel Feed and Return Pipe(1)»Connect—Plastic Collar Quick Connect Fitting Service



6. Fuel Feed and Return Pipe(4)@Retainer(3)»Engage
7. Tie Strap (2)»Install NEW
8. Fuel Return Pipe(1)»Connect—Metal Collar Quick Connect Fitting Service
9. { If equipped } Install the transfer case vent hose retainers.



10. Fuel Feed and Return Pipe(4)»Install
11. Fuel Return Pipe(3)»Connect—Metal Collar Quick Connect Fitting Service
12. Fuel Feed Pipe(2)»Connect—Metal Collar Quick Connect Fitting Service

Caution: Refer to Fastener Caution .

13. Fuel Feed and Return Front Hose Bracket Nut(1)»Install and tighten—Fastener Specifications
14. Connect all wiring harness retainers to the fuel feed and fuel return pipe.
15. Raise transmission to installed position.



16. If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
1. Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
2. Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
3. Apply thread locking adhesive to the external threads of the components.Adhesives, Fluids, Lubricants, and Sealers
4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
17. Front Axle Propeller Shaft(1)»Reposition
18. Align the reference marks made between the front axle propeller shaft (1) and the front differential drive pinion gear yoke.
19. Front Axle Propeller Shaft Washer(3)»Install[3x]
20. Install the 6 front axle propeller shaft bolts (2) and tighten in a crisscross pattern. Fastener Specifications



21. Transmission Support Crossmember(1)»Install



22. Transmission Support Crossmember Bolt(3)»Install[4x]
23. Transmission Support Crossmember Nut(2)»Install and tighten[4x]—Fastener Specifications
24. Transmission Mount Nut(1)»Install and tighten[2x]—Fastener Specifications
25. Remove the transmission jack.



26. { If equipped }Position the wiring harness (2) as necessary and install the harness retainers (1) into the transmission support crossmember.



27. {with F47} Automatic Level Control Air Supply Reservoir(2)»Install
28. {with F47} Install the 3 automatic level control air compressor bolts (1) and tighten. Fastener Specifications



29. {with F47} Install the chassis wire harness clip (1) to the automatic level control air supply reservoir.



30. {with F47} Install the air line (2) and clip the 2 air line retainers (1).
31. Install underbody panels as necessary.Underbody Panel Component Locator



32. Fuel Cooler Coolant Cooler Inlet Hose (2)»Install[2x]
33. Hose Clamp(1)»Engage[2x]—Hose Clamp Replacement Guidelines - Spring Type
34. Front Wheelhouse Liner-Left Side»Install—Front Wheelhouse Liner Replacement
35. Prime the fuel system and inspect for fuel leaks. Fuel System Priming