DTC P2714 or P2715
Diagnostic InstructionsDTC Descriptor
DTC P2714

Pressure Control Solenoid Valve 4 Stuck Off

DTC P2715

Pressure Control Solenoid Valve 4 Stuck On

Diagnostic Fault Information

Note: The components are listed from the least to the most intrusive to service.

Component

DTC

Condition

Q8 Control Solenoid Valve Assembly

P2714

  • Q27D Pressure Control Solenoid Valve 4—Binding or Sticking/Stuck
  • Control Solenoid Valve Assembly Filter Plate—BlockedorCracked
  • O-Ring—Leaking

Control Valve Channel Plate

P2714

Oil Channels or Orifices—Clogged/Restricted

Control Valve Channel Plate Spacer Plate

P2714

Oil Channels or Orifices—Clogged/Restricted

Control Valve Body

P2714, P2715

2-6 Clutch Regulator Valve—Binding or Sticking/Stuck

Automatic Transmission Fluid Filter

P2714

Oil Filter Assembly Pipe Seal—Leaking

Torque Converter with Fluid Pump Housing Assembly

P2714

Transmission Fluid Pump Housing—Scored/Worn

1-2-3-4 Clutch Backing Plate Retaining Ring

P2714

Retaining Ring—Not seated correctly

2-6 Clutch Assembly

P2714, P2715

  • 2-6 Clutch Spring Retaining Ring—Not seated correctly
  • 2-6 Clutch Piston—Seal Ring—Leaking
  • 2-6 clutch plates worn or damaged.
Circuit/System Description

For an overview of the component/system, refer to:

The solenoid valve directs fluid pressure to the 2-6 regulator valve that controls the fluid pressure to the 2-6 clutch.

DTC P2714, P2715 will set with a hydraulic/mechanical condition.

Conditions for Running the DTC
  • DTC P0101–P0103, P0106–P0108, P0171, P0172, P0174, P0175, P0201–P0208, P0300–P0308, P0401, P042E, P0716, P0717, P0722, P0723, P182E = Not set
  • { P2715 }2-6 Clutch=Commanded Off
  • Accelerator Pedal Position=Greater than 0.5%
  • Accelerator pedal position signal = Valid
  • Engine Speed=400 to 7,500 RPM
  • { P2715 }Engine Torque=Greater than 45 Nm (33 lb ft)
  • High Side Driver=Enabled
  • Ignition Voltage=9 to 32 V
  • Transmission Fluid Temperature=Warmer than 7°C (20°F)
  • Transmission Output Speed=Greater than 100 RPM
  • { P2714 }Transmission Range Command=2nd Gearor5th Gearor6th gear

Frequency the DTC runs=Continuously—After the running conditions are met—For greater than 5 s

Conditions for Setting the DTCP2714

2-6 Clutch=Not applied—For greater than 3 s

The above condition(s) must occur 3 times.

P2715

2-6 Clutch=Applied—For greater than 3 s

The above condition(s) must occur 3 times.

Actions Taken When the DTC Sets

DTCs listed in the DTC Descriptor category=Type A DTC—Additional actions taken:

  • Grade braking=Disabled
  • Line Pressure Command=Maximum
  • Manual Shift Control=Disabled
  • Mode Switch=Disabled—{ If equipped }
  • Neutral Idle Mode=Disabled—{ If equipped }
  • Powertrain braking=Disabled
  • Transmission Adaptive Pressure Control=Freeze current adapt values
  • { P2714 }Transmission gear allowed=3rd Gear
  • { P2715 }Transmission gear allowed=2nd Gear
Conditions for Clearing the DTC

DTCs listed in the DTC Descriptor category=Type A DTC

Reference Information

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References

Circuit/System Verification
  1. Verify the condition does not exist:Incorrect fluid level or condition»Refer to:Transmission Fluid Level and Condition Check
    • If a condition exists

      Repair or replace as necessary

    • If no condition exists
  2. Ignition » On / Vehicle » In Service Mode
  3. Clear the DTCs.
  4. Road test the vehicle.»Refer to:Road Test

    Verify DTC P0716, P0717, P0722,P0723 is not set

    • If none of the DTCs are set
  5. Verify DTC P2714, P2715 is not set
    • If DTC P2714 or P2715 is set

      Refer to:Circuit/System Testing

    • If none of the DTCs are set
  6. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

    Verify the DTC does not set.

    • If the DTC sets

      Refer to:Circuit/System Testing

    • If the DTC is not set
  7. All OK.
Circuit/System Testing
  1. Verify the condition does not exist:Incorrect pressure»Refer to:Line Pressure Check&Solenoid Valve Pressure
    • If no condition exists
  2. Ignition/Vehicle » Off
  3. Remove the component:Q8 Control Solenoid Valve Assembly
  4. Verify the procedure/test passes.»Refer to:Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test
    • If the procedure/test does not pass

      Replace the component:Q8 Control Solenoid Valve Assembly

    • If the procedure/test passes
  5. Refer to:Diagnostic Fault Information
Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair:Diagnostic Repair Verification

Additional Procedures

Transmission Adaptive Values Learn—Perform after any repair