Last Modified: 12-11-2024 6.11:8.1.0 Doc ID: RM100000002Q1PH
Model Year Start: 2025 Model: GR Corolla Prod Date Range: [09/2024 -           ]
Title: G16E-GTS (ENGINE CONTROL): SFI SYSTEM: P008700; Fuel Rail / System Pressure - Too Low; 2025 MY GR Corolla [09/2024 -        ]

DTC

P008700

Fuel Rail / System Pressure - Too Low

DESCRIPTION

The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor (for high pressure side), fuel pump assembly (for high pressure side) and direct fuel injector assemblies. The spill control valve adjusts the return volume of high-pressure fuel. The check valve mechanically opens and closes the path to the fuel delivery pipe. The relief valve releases the fuel back to the fuel tank if there is a malfunction in the high-pressure fuel system. The fuel pump assembly (for high pressure side) is installed to the cylinder head cover and operated by a cam installed to the exhaust camshaft. Rotation of the camshaft moves the pump plunger inside the fuel pump assembly (for high pressure side) up and down, pressurizing the fuel. The pressurized fuel opens the check valve and is pumped into the fuel delivery pipe. The ECM controls the spill control valve to adjust the fuel pressure between 4 and 26 MPa (40.8 and 265.1 kgf/cm 2 , 580 and 3770 psi) and monitors signals from the fuel pressure sensor (for high pressure side) to maintain the target fuel pressure.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Note

P008700

Fuel Rail / System Pressure - Too Low

Either of the following conditions is met (1 trip detection logic):

  • The actual fuel pressure is lower than the target fuel pressure value by 5 MPa (51.0 kgf/cm 2 , 725 psi) or more for 10 seconds or more during in-cylinder injection.
  • The actual fuel pressure value is lower than the target fuel pressure value by 2 MPa (20.4 kgf/cm 2 , 290 psi) or more for 15 seconds or more during port injection only.
  • Leak of fuel
  • Fuel pipe (fuel tank - fuel pump assembly (for high pressure side))
  • Fuel pipe (fuel pump assembly (for high pressure side) - direct fuel injector assembly)
  • Direct fuel injector assembly
  • Fuel pump assembly (for high pressure side)
  • Fuel pump (for low pressure side)
  • Fuel pressure sensor (for high pressure side)
  • Fuel system
  • ECM

Comes on

SAE Code: P0087

MONITOR DESCRIPTION

If the fuel pressure (for high pressure side) decreases despite an increase request signal being sent to the fuel pump assembly (for high pressure side) by the ECM, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Related DTCs

P0087: Fuel pressure too low

Required Sensors/Components (Main)

Fuel pressure sensor (for high pressure side)

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

About 10 seconds

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Fuel pressure sensor (for high pressure side) malfunction (P0192, P0193)

Not detected

High pressure fuel pump malfunction (P1235)

Not detected

Fuel injector driver malfunction (P0201, P0202, P0203, P062D)

Not detected

Time after engine start

0.2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

When Using Direct Injection

-

Duration that both of the following conditions (a) and (b) are met

10 seconds or more

(a) Difference in fuel pressure between actual and target

Less than -5 MPa (-51.0 kgf/cm 2 , -725 psi)

(b) Actual discharge rate of high pressure fuel pump

325 mm 3 /st or more

When Using Only Port Injection

-

Duration that both of the following conditions (a) and (b) are met

15 seconds or more

(a) Difference in fuel pressure between actual and target

Less than -2 MPa (-20.4 kgf/cm 2 , -290 psi)

(b) Actual discharge rate of high pressure fuel pump

125 mm 3 /st or more

CONFIRMATION DRIVING PATTERN

HINT:

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • Permanent misfire and fuel system DTCs can only be cleared when performing the universal trip driving pattern when no malfunction is detected.
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the GTS on.
  4. Record the Freeze Frame Data.
  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  6. Turn the ignition switch off and wait for at least 30 seconds.
  7. Start the engine.
  8. Turn GTS on.
  9. Based on the engine speed, engine load, injection mode and other conditions displayed in the Freeze Frame Data, reproduce the conditions present when the DTC was stored.
  10. Enter the following menus: Powertrain / Engine / Trouble Codes.
  11. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  13. Input the DTC: P008700.
  14. Check the DTC judgment result.

    GTS Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system has a malfunction.

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK FUEL LEAK

(a) Check around and beneath the vehicle for fuel leaks, fumes, etc.

OK:

No fuel leaks present.

NG

REPAIR OR REPLACE FUEL LEAK POINT

OK

2.

CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008700)

(a) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

P008700 is output

A

P008700 and other DTCs are output

B

HINT:

If any DTCs other than P008700 are output, troubleshoot those DTCs first.

B

GO TO DTC CHART

A

3.

CHECK SHORTAGE OF FUEL

(a) In accordance with the display on the GTS, check the value of Freeze Frame Data item "Fuel Remaining Volume" stored when the DTC was detected.

Powertrain > Engine > DTC(P008700) > Freeze Frame Data

Tester Display

Fuel Remaining Volume

Standard:

Freeze Frame Data Item

Specified Condition

Fuel Remaining Volume

More than 15%

HINT:

  • DTC P008700 may be stored if the engine stopped after running out of fuel or the vehicle temporarily ran out of fuel when the amount of fuel was low.
  • If Freeze Frame Data item "Fuel Remaining Volume" is not displayed, based on the interview with the customer, check if the low fuel level warning was not displayed when the MIL illuminated.
NEXT

4.

READ FREEZE FRAME DATA (TARGET FUEL PRESSURE (LOW) / TARGET FUEL PRESSURE 2 AND LOW FUEL PRESSURE SENSOR)

Pre-procedure1

(a) Using the GTS, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

HINT:

  • Check the Freeze Frame Data sets recorded the moment the DTC was stored and after the DTC was stored.
  • Using the Freeze Frame Data, confirm the vehicle conditions when the DTC was stored, such as if the engine was idling with the shift state P, D or N or neutral or if the vehicle was being driven at a constant speed or accelerating.

Powertrain > Engine > DTC(P008700) > Freeze Frame Data

Tester Display

Target Fuel Pressure (Low) / Target Fuel Pressure 2

Low Fuel Pressure Sensor

Procedure1

(b) Compare the difference in pressure between "Target Fuel Pressure (Low) / Target Fuel Pressure 2 and Low Fuel Pressure Sensor".

Result

Proceed to

Difference between Target Fuel Pressure (Low) / Target Fuel Pressure 2 and Low Fuel Pressure Sensor is within 200 kPa

A

Difference between Target Fuel Pressure (Low) / Target Fuel Pressure 2 and Low Fuel Pressure Sensor is more than 200 kPa

B

Post-procedure1

(c) None.

B

GO TO FUEL PUMP CONTROL CIRCUIT

A

5.

CHECK MISFIRE COUNT OF DIRECT INJECTION

(a) Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

(b) Enter the following menus.

Powertrain > Engine > Active Test

Active Test Display

Control the Injection Mode

Data List Display

Injection Mode

Misfire Count Cylinder #1

Misfire Count Cylinder #2

Misfire Count Cylinder #3

(c) According to the display on the GTS, read the Data List with the Active Test "Control the Injection Mode" set to Direct.

Injection Mode

Misfire Count

Proceed to

Direct

No misfire counts, or misfire counts occur randomly in all cylinders

A

Misfire counts occur in a particular cylinder

B

HINT:

Perform "Inspection After Repair" after replacing the direct fuel injector assembly.

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

B

REPLACE DIRECT FUEL INJECTOR ASSEMBLY

A

6.

CHECK FUEL PUMP OPERATION (FOR LOW PRESSURE SIDE)

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (FUEL): FUEL SYSTEM: ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

NG

GO TO FUEL PUMP CONTROL CIRCUIT

OK

7.

CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (FUEL): FUEL SYSTEM: ON-VEHICLE INSPECTION+

NG

REPAIR OR REPLACE FUEL SYSTEM

OK

8.

READ VALUE USING GTS (FUEL PRESSURE (HIGH))

Pre-procedure1

(a) Discharge the fuel pressure.

HINT:

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

(1) Remove the EFI-MAIN NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.

(2) Start the engine.

(3) After the engine has stopped on its own, turn the ignition switch off.

HINT:

If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.

(4) Crank the engine again and make sure that the engine does not start.

(5) Install the EFI-MAIN NO. 2 fuse.

(b) Turn the ignition switch to ON.

Procedure1

(c) According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List

Tester Display

Fuel Pressure (High)

HINT:

Use the snapshot function to record the value displayed or make a note of it.

Post-procedure1

(d) None.

Pre-procedure2

(e) Start the engine.

Procedure2

(f) Read the change in the Data List item "Fuel Pressure (High)" after discharging the fuel system pressure and after starting the engine.

Powertrain > Engine > Data List

Tester Display

Fuel Pressure (High)

OK:

The value of the Data List item "Fuel Pressure (High)" changes.

Post-procedure2

(g) None.

NG

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

OK

9.

CLEAR DTC

(a) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(b) Turn the ignition switch off and wait for at least 30 seconds.

NEXT

10.

CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008700 IS OUTPUT AGAIN)

(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(b) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

P008700 is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

HINT:

DTC P008700 may be stored if the engine stopped after running out of fuel or the vehicle temporarily ran out of fuel when the amount of fuel was low.

B

REPLACE ECM