- Back door opener
| Last Modified: 01-27-2025 | 6.11:8.1.0 | Doc ID: RM100000002Q05E |
| Model Year Start: 2025 | Model: GR Corolla | Prod Date Range: [09/2024 - ] |
| Title: G16E-GTS (STARTING): STARTER: REMOVAL; 2025 MY GR Corolla [09/2024 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during starter assembly removal/installation are shown below.
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
|
Effect/Inoperative Function when Necessary Procedure not Performed |
Necessary Procedure |
Link |
|---|---|---|
|
Front Camera System |
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. |
|
Learning completes when vehicle is operated normally
|
Effect/Inoperative Function when Necessary Procedure not Performed |
Necessary Procedure |
Link |
|---|---|---|
|
Power Door Lock Control System |
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
2. REMOVE DECK BOARD ASSEMBLY
Click here
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
4. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here
5. DRAIN ENGINE COOLANT
Click here
6. DRAIN ENGINE OIL
Click here
7. REMOVE OIL PRESSURE AND TEMPERATURE SENSOR
Click here
8. DISCONNECT NO. 6 WATER BY-PASS HOSE
Click here
9. DISCONNECT NO. 5 WATER BY-PASS HOSE
Click here
10. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY
Click here
11. REMOVE RADIATOR SUPPORT OPENING COVER (for Automatic Transaxle)
Click here
12. REMOVE INLET NO. 1 AIR CLEANER (for Automatic Transaxle)
Click here
13. REMOVE AIR CLEANER WITH AIR CLEANER HOSE (for Automatic Transaxle)
Click here
14. DISCONNECT NO. 1 RADIATOR HOSE (for Automatic Transaxle)
Click here
15. REMOVE NO. 2 AIR TUBE (for Automatic Transaxle)
Click here
16. REMOVE NO. 4 AIR HOSE (for Automatic Transaxle)
Click here
17. REMOVE NO. 5 AIR HOSE (for Automatic Transaxle)
Click here
18. DISCONNECT TRANSMISSION OIL COOLER (for Automatic Transaxle)
|
(a) Remove the 2 bolts and disconnect the transmission oil cooler from the oil cooler bracket. |
|
|
(b) Disengage the clamp. |
|
19. DISCONNECT ENGINE WIRE (for Automatic Transaxle)
|
(a) Disengage the 2 clamps. |
|
(b) Remove the bolt and disengage the guide and disconnect the engine wire.
20. REMOVE FLYWHEEL HOUSING SIDE COVER
|
(a) Disengage the claw as shown in the illustration to remove the flywheel housing side cover. |
|
21. REMOVE STARTER ASSEMBLY
|
(a) Disconnect the starter assembly connector. |
|
(b) Open the terminal cap.
|
(c) Disengage the clamp to separate the engine wire. |
|
(d) Remove the nut and disconnect the engine wire from terminal 30.
(e) Remove the 2 bolts and starter assembly from the cylinder block sub-assembly.
NOTICE:
Make sure that the flywheel housing under cover is securely installed.
Click here
|
(f) Remove the bolt and wire harness clamp bracket from the starter assembly. |
|
|
|