- CAN main bus line, CAN branch line or connector
- Central gateway ECU (network gateway ECU)
- Tire pressure warning ECU and receiver
-
4WD ECU Assembly
(for G16E-GTS)
- No. 16 CAN junction connector
| Last Modified: 06-05-2026 | 6.11:8.1.0 | Doc ID: RM100000002DUK2 |
| Model Year Start: 2024 | Model: GR Corolla | Prod Date Range: [08/2023 - ] |
| Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): Check Bus 6 Line; 2024 - 2026 MY GR Corolla Corolla Corolla Hatchback [08/2023 - ] | ||
|
Check Bus 6 Line |
DESCRIPTION
|
Symptom |
Trouble Area |
|---|---|
|
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen. |
|
WIRING DIAGRAM
except G16E-GTS
for G16E-GTS
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
-
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
![2024 - 2025 MY GR Corolla Corolla Corolla Hatchback [08/2023 - 09/2024]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
- Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 10 minutes or more before measuring the resistance.
-
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click here
-
When disconnecting and reconnecting the battery.
HINT:
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
-
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
-
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
-
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
|
1. |
CHECK FOR OPEN IN CAN MAIN BUS LINES |
(a) Disconnect the cable from the negative (-) battery terminal.
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance
|
|
| NG |
|
|
|
2. |
CHECK FOR SHORT IN CAN BUS LINES |
|
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance
|
|
| NG |
|
|
|
3. |
CHECK FOR SHORT TO +B IN CAN BUS LINE |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
- |
- |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I173-31 (CA7H) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I173-32 (CA7L) - I26-16 (BAT) |
| NG |
|
|
|
4. |
CHECK FOR SHORT TO GND IN CAN BUS LINE |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
- |
- |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I173-31 (CA7H) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I173-32 (CA7L) - I26-4 (CG) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
|
|
5. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
except G16E-GTS |
A |
|
for G16E-GTS |
B |
| B |
|
|
|
6. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
for Hatchback |
A |
|
for Sedan |
B |
| B |
|
|
|
7. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I215 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-1 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I215-7 (CANL) - I26-4 (CG) |
| NG |
|
|
|
8. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-2 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I215-8 (CANL) - I26-4 (CG) |
| NG |
|
|
|
9. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-3 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I215-9 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
10. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-1 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I215-7 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
11. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-2 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I215-8 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
12. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 or O171 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-3 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I215-9 (CANL) - I26-4 (CG) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
13. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I236 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-1 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I236-12 (CANL) - I26-4 (CG) |
| NG |
|
|
|
14. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-2 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I236-13 (CANL) - I26-4 (CG) |
| NG |
|
|
|
15. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-3 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I236-14 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
16. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-1 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I236-12 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
17. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-2 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I236-13 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
18. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 or O171 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-3 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I236-14 (CANL) - I26-4 (CG) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
19. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I189 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-2 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-6 (CANL) - I26-4 (CG) |
| NG |
|
|
|
20. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-3 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-7 (CANL) - I26-4 (CG) |
| NG |
|
|
|
21. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-4 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-8 (CANL) - I26-4 (CG) |
| NG |
|
|
|
22. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to 4WD ECU Assembly |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-1 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-5 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
23. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-2 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-6 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
24. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-3 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-7 (CANL) - I26-4 (CG) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
25. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-4 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-8 (CANL) - I26-4 (CG) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
26. |
CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
(a) Disconnect the O177 4WD ECU assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to 4WD ECU Assembly |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-1 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
I189-5 (CANL) - I26-4 (CG) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
|
27. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
except G16E-GTS |
A |
|
for G16E-GTS |
B |
| B |
|
|
|
28. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
for Hatchback |
A |
|
for Sedan |
B |
| B |
|
|
|
29. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I215 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-1 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I215-7 (CANL) - I26-16 (BAT) |
| NG |
|
|
|
30. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-2 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I215-8 (CANL) - I26-16 (BAT) |
| NG |
|
|
|
31. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-3 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I215-9 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
32. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-1 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I215-7 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
33. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-2 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I215-8 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
34. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 or O171 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-3 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I215-9 (CANL) - I26-16 (BAT) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
35. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I236 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-1 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I236-12 (CANL) - I26-16 (BAT) |
| NG |
|
|
|
36. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-2 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I236-13 (CANL) - I26-16 (BAT) |
| NG |
|
|
|
37. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-3 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I236-14 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
38. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-1 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I236-12 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
39. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-2 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I236-13 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
40. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 or O171 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-3 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I236-14 (CANL) - I26-16 (BAT) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
41. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I189 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-2 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-6 (CANL) - I26-16 (BAT) |
| NG |
|
|
|
42. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-3 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-7 (CANL) - I26-16 (BAT) |
| NG |
|
|
|
43. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-4 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-8 (CANL) - I26-16 (BAT) |
| NG |
|
|
|
44. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
(a) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to 4WD ECU Assembly |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-1 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-5 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
45. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-2 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-6 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
46. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-3 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-7 (CANL) - I26-16 (BAT) |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
47. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-4 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-8 (CANL) - I26-16 (BAT) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
48. |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
(a) Disconnect the O177 4WD ECU assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to 4WD ECU Assembly |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-1 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
I189-5 (CANL) - I26-16 (BAT) |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
|
49. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
except G16E-GTS |
A |
|
for G16E-GTS |
B |
| B |
|
|
|
50. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
for Hatchback |
A |
|
for Sedan |
B |
| B |
|
|
|
51. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I215 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-1 (CANH) - I215-7 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
52. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-2 (CANH) - I215-8 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
53. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-3 (CANH) - I215-9 (CANL) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
54. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-1 (CANH) - I215-7 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
55. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-2 (CANH) - I215-8 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
56. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 or O171 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-3 (CANH) - I215-9 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
57. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I236 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-1 (CANH) - I236-12 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
58. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-2 (CANH) - I236-13 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
59. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-3 (CANH) - I236-14 (CANL) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
60. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-1 (CANH) - I236-12 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
61. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-2 (CANH) - I236-13 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
62. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 or O171 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-3 (CANH) - I236-14 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
63. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I189 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-2 (CANH) - I189-6 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
64. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-3 (CANH) - I189-7 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
65. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-4 (CANH) - I189-8 (CANL) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
| NG |
|
|
|
66. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to 4WD ECU Assembly |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-1 (CANH) - I189-5 (CANL) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
| NG |
|
|
67. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-2 (CANH) - I189-6 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
68. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-3 (CANH) - I189-7 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
|
69. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the O170 tire pressure warning ECU and receiver connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-4 (CANH) - I189-8 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) |
|
70. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
(a) Disconnect the O177 4WD ECU assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to 4WD ECU Assembly |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-1 (CANH) - I189-5 (CANL) |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 16 CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) |
|
71. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
except G16E-GTS |
A |
|
for G16E-GTS |
B |
| B |
|
|
|
72. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
Result
|
Result |
Proceed to |
|---|---|
|
for Hatchback |
A |
|
for Sedan |
B |
| B |
|
|
|
73. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I215 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-1 (CANH) - I215-7 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
74. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I215-2 (CANH) - I215-8 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
|
|
75. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Reconnect the I215 No. 16 CAN junction connector.
(b) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance
|
|
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 16 CAN JUNCTION CONNECTOR) |
|
76. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I236 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-1 (CANH) - I236-12 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
77. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I236-2 (CANH) - I236-13 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
|
|
78. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Reconnect the I236 No. 16 CAN junction connector.
(b) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance
|
|
| OK |
|
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
Click here
|
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 16 CAN JUNCTION CONNECTOR) |
|
79. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the I189 No. 16 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-2 (CANH) - I189-6 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
|
|
80. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of wire harness connector (to No. 16 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I189-3 (CANH) - I189-7 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK |
|
REPLACE NO. 16 CAN JUNCTION CONNECTOR |
|
|
81. |
CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Reconnect the I189 No. 16 CAN junction connector.
(b) Disconnect the I173 central gateway ECU (network gateway ECU) connector.
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance
|
|
|
|
|
|