| Last Modified: 12-11-2024 | 6.11:8.1.0 | Doc ID: RM100000002D8AZ |
| Model Year Start: 2024 | Model: GR Corolla | Prod Date Range: [08/2023 - 09/2024] |
| Title: PARK ASSIST / MONITORING: ULTRASONIC SENSOR (for Front Side): INSTALLATION; 2024 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [08/2023 - 09/2024] | ||
INSTALLATION
PROCEDURE
1. INSTALL ULTRASONIC SENSOR CUSHION SET
HINT:
Only perform this procedure when removing and installing the ultrasonic sensor cushion set.
(a) Install the ultrasonic sensor cushion set as shown in the illustration.
|
Install in this Direction |
- |
- |
2. INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER
HINT:
- Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.
- If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.
(a) Clean the surface of the front bumper assembly.
(1) Remove any remaining double-sided tape from the front bumper assembly.
(2) Wipe off any adhesive residue with cleaner.
|
(b) Cover the sensor installation hole with a 31 mm (1.22 in.) circular piece of tape. |
|
(c) Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.
|
*A |
for LH Side |
*B |
for RH Side |
|
Primer |
- |
- |
NOTICE:
- Use a clean brush or felt.
- Do not touch the front bumper assembly until the primer has dried.
(d) Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.
(e) Peel off the release paper from a new front corner ultrasonic sensor retainer.
(f) Align the front corner ultrasonic sensor retainer with the mark on the front bumper assembly and install it as shown in the illustration.
|
*A |
for LH Side |
*B |
for RH Side |
|
*a |
Scribed Line |
- |
- |
|
Press Here |
- |
- |
NOTICE:
- Ensure that the front corner ultrasonic sensor retainer is within the scribed line.
- The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.
HINT:
Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper assembly.
3. INSTALL FRONT CORNER ULTRASONIC SENSOR
HINT:
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
(a) Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.
|
|
Install in this Direction |
(b) Connect the connector.
4. INSTALL FRONT CENTER ULTRASONIC SENSOR
HINT:
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
(a) Engage the 2 claws to install the front center ultrasonic sensor as shown in the illustration.
|
|
Install in this Direction |
(b) Connect the connector.
5. INSTALL NO. 3 RADIATOR TO SUPPORT SEAL
Click here
![2024 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [08/2023 - 09/2024]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Hatchback, GR): REASSEMBLY+](/t3Portal/stylegraphics/info.gif)
6. INSTALL NO. 2 RADIATOR TO SUPPORT SEAL
HINT:
Use the same procedure as for the No. 3 radiator to support seal.
7. INSTALL FRONT BUMPER ASSEMBLY
Click here
8. PERFORM CALIBRATION
Click here
SST: 09989-00020
|
|