| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000002D8AH |
| Model Year Start: 2024 | Model: GR Corolla | Prod Date Range: [08/2023 - ] |
| Title: PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: C1AE487; Ultrasonic Sensor (Front Right Corner) Missing Message; 2024 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [08/2023 - ] | ||
|
DTC |
C1AE487 |
Ultrasonic Sensor (Front Right Corner) Missing Message |
DESCRIPTION
This DTC is stored when an open circuit or short occurs in the communication line between the front corner ultrasonic sensor RH and the front center ultrasonic sensor RH, or when a malfunction occurs in the front corner ultrasonic sensor RH.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
DTC Output from |
Priority |
|---|---|---|---|---|---|
|
C1AE487 |
Ultrasonic Sensor (Front Right Corner) Missing Message |
Front corner ultrasonic sensor RH lost communication |
|
Clearance Warning |
B |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click here
![2024 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [08/2023 - ]; PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: CALIBRATION](/t3Portal/stylegraphics/info.gif)
- If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.
-
If C1AE396 is output at the same time, check C1AE396 first.
Click here
PROCEDURE
|
1. |
CHECK DTC |
(a) If DTC C1AE396 is output, perform troubleshooting for DTC C1AE396 first.
Body Electrical > Clearance Warning > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
C1AE396 is not output |
A |
|
C1AE396 is output |
B |
| B |
|
|
|
2. |
VEHICLE CONDITION AND WORK DETAILS CHECK |
(a) Check the vehicle condition and work details.
|
Result |
Proceed to |
|---|---|
|
The clearance warning ECU assembly or ultrasonic sensor has not been replaced |
A |
|
The clearance warning ECU assembly or ultrasonic sensor has been replaced |
B |
| B |
|
|
|
3. |
CHECK CONNECTOR CONNECTION CONDITION (ULTRASONIC SENSOR) |
(a) Check that the connector is properly connected to the front corner ultrasonic sensor and front center ultrasonic sensor.
|
|
4. |
CHECK FOR DTC |
(a) According to the display on the GTS, check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
(b) According to the display on the GTS, clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
(c) Recheck for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
C1AE487 is not output |
A |
|
C1AE487 is output |
B |
| A |
|
END (CONNECTOR CONNECTION MALFUNCTION) |
|
|
5. |
CHECK CONNECTOR CONNECTION CONDITION (CLEARANCE WARNING ECU ASSEMBLY) |
(a) Check that the connector is properly connected to the clearance warning ECU assembly.
|
|
6. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
|
7. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE187, C1AE287, C1AE387 and C1AE487 are output |
B |
|
C1AE287, C1AE387 and C1AE487 are output |
C |
|
C1AE387 and C1AE487 are output |
D |
|
C1AE487 is output |
E |
| A |
|
| B |
|
GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE187)) |
| C |
|
GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE287)) |
| D |
|
GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE387)) |
|
|
8. |
CHECK WIRE HARNESS AND CONNECTOR (FRONT CENTER ULTRASONIC SENSOR RH - FRONT CORNER ULTRASONIC SENSOR RH) |
Pre-procedure1
(a) Disconnect the B3 front center ultrasonic sensor RH connector.
(b) Disconnect the B4 front corner ultrasonic sensor RH connector.
Procedure1
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B3-1 (BO) - B4-4 (BI) |
Always |
Below 1 Ω |
|
B3-2 (SO) - B4-5 (SI) |
Always |
Below 1 Ω |
|
B3-3 (EO) - B4-6 (EI) |
Always |
Below 1 Ω |
|
B3-1 (BO) or B4-4 (BI) - Body ground |
Always |
10 kΩ or higher |
|
B3-2 (SO) or B4-5 (SI) - Body ground |
Always |
10 kΩ or higher |
|
B3-3 (EO) or B4-6 (EI) - Body ground |
Always |
10 kΩ or higher |
Post-procedure1
(d) None
| NG |
|
REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR |
|
|
9. |
REPLACE FRONT CORNER ULTRASONIC SENSOR RH |
(a) Replace the front corner ultrasonic sensor RH with a new or normally functioning one.
HINT:
-
Click here
- To check if the ultrasonic sensor is functioning correctly, replace it with another ultrasonic sensor.
|
|
10. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
|
11. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE487 is output |
B |
| A |
|
END (FRONT CORNER ULTRASONIC SENSOR RH WAS DEFECTIVE) |
| B |
|
|
|