BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): C055895; Right Rear Wheel Speed Sensor Incorrect Component Installed; 2024 - 2025 MY Corolla Corolla Hatchback GR Corolla [08/2023

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000002D0EU
Model Year Start: 2024	Model: GR Corolla	Prod Date Range: [08/2023 - ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): C055895; Right Rear Wheel Speed Sensor Incorrect Component Installed; 2024 - 2025 MY Corolla Corolla Hatchback GR Corolla [08/2023 - ]

DTC

C055895

Right Rear Wheel Speed Sensor Incorrect Component Installed

DESCRIPTION

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	MIL	Note
C055895	Right Rear Wheel Speed Sensor Incorrect Component Installed	The rear speed sensor RH is installed incorrectly.	Rear speed sensor RH (rear axle hub and bearing assembly RH)	Comes on	SAE Code: C0558

MONITOR DESCRIPTION

The skid control ECU (brake actuator assembly) has a speed sensor circuit self-diagnosis function.

When the vehicle is stopped, the speed sensor supply voltage exceeds a certain value, and the self-diagnosis function detects an incorrectly installed speed sensor, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Related DTCs	C0558 (Case 1): Wheel speed sensor wrong sensor type monitoring for RR (PWM intelligent sensor) C0558 (Case 2): Wheel speed sensor wrong sensor type monitoring for RR (standard sensor) C0558 (Case 3): Wheel speed sensor wrong sensor type monitoring for RR (intelligent sensor)
Required Sensors/Components(Main)	Skid control ECU (brake actuator assembly)
Required Sensors/Components(Related)	Skid control ECU (brake actuator assembly) Speed sensor
Frequency of Operation	Continuous
Duration	3 seconds
MIL Operation	2 driving cycles
Sequence of Operation	None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored	TMC's intellectual property
Other conditions belong to TMC's intellectual property	-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

COMPONENT OPERATING RANGE

TMC's intellectual property

CONFIRMATION DRIVING PATTERN

NOTICE:

When performing the normal judgment procedure, make sure that the driver door is closed and is not opened at any time during the procedure.

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the GTS on.
Wait for 3 seconds or more. [*]
HINT:

[*]: Normal judgment procedure.

The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
Enter the following menus: Chassis / Brake/EPB* / Utility / All Readiness.
*: Electric Parking Brake System
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform driving pattern again.

PROCEDURE

1.	CHECK PART NUMBER (REAR SPEED SENSOR RH)

(a) Check that the rear speed sensor RH is installed.

OK:

Proper rear speed sensor RH is installed.

NOTICE:

If it is necessary to remove components in order to check the rear speed sensor RH, follow the relevant installation and removal procedures and precautions for those components.

HINT:

The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

for Double Wishbone Type Suspension: Click here

for Torsion Beam Type Suspension: Click here

CLEAR DTC

(a) Clear the DTCs.

Chassis > Brake > Clear DTCs

(b) Turn the ignition switch off.

3.	RECONFIRM DTC

(a) Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.

(b) Check if the same DTC is output.

Chassis > Brake > Trouble Codes

HINT:

The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.

Result	Proceed to
DTC C055895 is not output.	A
DTC C055895 is output.	B

USE SIMULATION METHOD TO CHECK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

for Double Wishbone Type Suspension: Click here

for Torsion Beam Type Suspension: Click here