Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM1000000029CK7 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM (w/ Safe Exit Assist Function): HOW TO PROCEED WITH TROUBLESHOOTING; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] |
HOW TO PROCEED WITH TROUBLESHOOTING
|
CAUTION / NOTICE / HINT
HINT:
-
Use the following procedure to troubleshoot the blind spot monitor system.
-
*: Use the GTS.
PROCEDURE
1.
|
VEHICLE BROUGHT TO WORKSHOP
|
NEXT
|
|
|
2.
|
CUSTOMER PROBLEM ANALYSIS
|
HINT:
If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.
NEXT
|
|
|
3.
|
INSPECT AUXILIARY BATTERY VOLTAGE
|
(a) Measure the auxiliary battery voltage with the ignition switch off.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
NEXT
|
|
|
4.
|
CHECK CAN COMMUNICATION SYSTEM*
|
(a) Use the GTS to check if the CAN communication system is functioning normally.
-
for Gasoline Model: Click here
-
for HV Model: Click here
Result
|
Proceed to
|
CAN communication system DTCs are not output
|
A
|
CAN communication system DTCs are output (for Gasoline Model)
|
B
|
CAN communication system DTCs are output (for HV Model)
|
C
|
A
|
|
|
5.
|
CHECK FOR DTC AND FREEZE FRAME DATA*
|
(a) Refer to DTC Check / Clear for the blind spot monitor system.
Body Electrical > Blind Spot Monitor "B" > Trouble Codes
Body Electrical > Blind Spot Monitor "A" > Trouble Codes
(b) Record or print DTCs and freeze frame data, if necessary.
Click here
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTCs are output
|
B
|
A
|
|
|
6.
|
PROBLEM SYMPTOMS TABLE
|
(a) Refer to Problem Symptoms Table.
Click here
Result
|
Proceed to
|
Fault is not listed in Problem Symptoms Table
|
A
|
Fault is listed in Problem Symptoms Table
|
B
|
HINT:
If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.
Click here
A
|
|
|
7.
|
PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*
|
(a) Refer to Terminals of ECU.
Click here
(b) Refer to Diagnosis System.
Click here
(c) Refer to Data List / Active Test.
Click here
NEXT
|
|
|
8.
|
ADJUST, REPAIR OR REPLACE
|
Result
|
Proceed to
|
When adjusting or repairing
|
A
|
When replacing
|
B
|
A
|
|
|
(a) Clear the DTCs.
Body Electrical > Blind Spot Monitor "B" > Clear DTCs
Body Electrical > Blind Spot Monitor "A" > Clear DTCs
10.
|
PERFORM BEAM AXIS CONFIRMATION
|
(a) Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.
Click here
NEXT
|
|
|
11.
|
PERFORM CONFIRMATION TEST*
|
NEXT |
|
END
|
|