Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000294YU
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): B2780; Push Switch / Key Unlock Warning Switch Malfunction; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]

DTC

B2780

Push Switch / Key Unlock Warning Switch Malfunction

DESCRIPTION

This DTC is stored if the transponder key ECU assembly does not detect that the unlock warning switch assembly is on even when the ignition switch is ON.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B2780

Push Switch / Key Unlock Warning Switch Malfunction

The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip detection logic*).

  • Wire harness or connector
  • Unlock warning switch assembly
  • Transponder key ECU assembly

DTC Output Confirmation Operation:

  • Insert the door control transmitter assembly into the ignition key cylinder.
  • *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Operation when Malfunction Detected

  • Hybrid control system cannot be started*1
  • Engine cannot be started*2

-

  • *1: for HV Model
  • *2: for Gasoline Model

Related Data List and Active Test

DTC No.

Data List and Active Test

B2780

Key SW

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • If the transponder key ECU assembly is replaced, refer to Registration.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): REGISTRATION 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): REGISTRATION

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

1.

INSPECT UNLOCK WARNING SWITCH ASSEMBLY

(a) Remove the unlock warning switch assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; DOOR LOCK: UNLOCK WARNING SWITCH: REMOVAL

(b) Inspect the unlock warning switch assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; DOOR LOCK: UNLOCK WARNING SWITCH: INSPECTION

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

OK

2.

CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY - BODY GROUND)

(a) Disconnect the I67 transponder key ECU assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I13-1 (UN+) - I67-5 (KSW)

Always

Below 1 Ω

I13-2 (UN-) - Body ground

Always

Below 1 Ω

I13-1 (UN+) or I67-5 (KSW) - Other terminals and body ground

Always

10 kΩ or higher

OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: TRANSPONDER KEY ECU: REMOVAL 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: TRANSPONDER KEY ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR