Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000293JL |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMC Made): C050623; Right Front Wheel Speed Sensor Signal Stuck Low; 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [11/2022 - ] |
DTC
|
C050623
|
Right Front Wheel Speed Sensor Signal Stuck Low
|
DESCRIPTION
Refer to DTC C050612.
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
C050623
|
Right Front Wheel Speed Sensor Signal Stuck Low
|
Any of the following is detected:
-
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.
-
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
-
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more.
|
-
Speed sensor installation
-
Wire harness and connector
-
Front speed sensor RH
-
Front speed sensor rotor RH (front axle hub sub-assembly RH)
|
WIRING DIAGRAM
Refer to DTC C050612.
Click here
PROCEDURE
1.
|
CHECK FRONT SPEED SENSOR RH INSTALLATION
|
(a) Check the front speed sensor RH installation.
OK:
There is no clearance between the front speed sensor RH and front steering knuckle RH.
The installation bolt is tightened properly.
Torque
8.5 N*m (87 kgf*cm, 75 in.*lbf)
|
|
*1
|
Front Speed Sensor RH
|
*a
|
Correct
|
*b
|
Incorrect
|
*c
|
8.5 N*m (87 kgf*cm, 75 in.*lbf)
|
*d
|
No clearance
|
|
|
OK
|
|
|
2.
|
CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
|
(a) Remove the front speed sensor RH.
Click here
(b) Check the front speed sensor tip RH.
OK:
The front speed sensor tip RH is free of scratches, oil, and foreign matter.
NOTICE:
-
If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.
-
If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.
NG |
|
CLEAN OR REPLACE FRONT SPEED SENSOR RH
|
OK
|
|
|
3.
|
READ VALUE USING GTS (FR WHEEL SPEED)
|
(a) Start the engine.
(b) Perform a road test.
(c) Check the front speed sensor RH output value.
Chassis > Brake/EPB > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
FR Wheel Speed
|
Front wheel speed sensor RH reading
|
Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
|
Vehicle stopped: 0.0 km/h (0.0 mph)
|
When driving at constant speed: No large fluctuations
|
Chassis > Brake/EPB > Data List
Tester Display
|
FR Wheel Speed
|
OK:
The output value changes in accordance with the vehicle speed.
NG
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE ACTUATOR ASSEMBLY)
|
(a) Turn the ignition switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the A140 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the A34 front speed sensor RH connector.
(e) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A34-2 (FR+) - A140-7 (FR+)
|
Always
|
Below 1 Ω
|
A34-2 (FR+) or A140-7 (FR+) - Body ground
|
Always
|
10 kΩ or higher
|
A34-1 (FR-) - A140-6 (FR-)
|
Always
|
Below 1 Ω
|
A34-1 (FR-) or A140-6 (FR-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
|
(a) Remove the component with the front speed sensor rotor RH.
Click here
(b) Check the front speed sensor rotor RH.
OK:
The front speed sensor rotor RH is free of scratches, oil, and foreign matter.
NOTICE:
-
If there is oil or foreign matter on the front speed sensor rotor RH, clean the front speed sensor rotor RH.
-
Do not use parts cleaner when cleaning the front speed sensor rotor RH.
-
If the front speed sensor rotor RH is damaged, replace the front speed sensor rotor RH with a new one.
HINT:
-
The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.
-
If the front speed sensor rotor RH needs to be replaced, replace it together with the front axle hub sub-assembly RH.
Result
|
Proceed to
|
OK
|
A
|
NG (The front speed sensor rotor RH is damaged.)
|
B
|
NG (There is foreign matter on the front speed sensor rotor RH.)
|
C
|
C |
|
CLEAN FRONT SPEED SENSOR ROTOR RH
|
|