| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000028W6Y |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: SEAT: FRONT SEAT ASSEMBLY (for Power Seat): INSTALLATION; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] | ||
INSTALLATION
CAUTION / NOTICE / HINT
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. INSTALL FRONT SEAT ASSEMBLY LH
|
(a) Place the front seat assembly LH in the cabin. NOTICE: Be careful not to damage the vehicle body. |
|
(b) Connect the front seat airbag assembly LH connector under the front seat assembly LH.
(1) Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.
|
*a |
Correct |
*b |
Incorrect |
|
*c |
Yellow CPA |
*d |
White Housing Lock |
(2) Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).
NOTICE:
- When connecting any airbag connector, take care not to damage the airbag wire harness.
- When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.
(c) Connect each connector and engage each clamp under the front seat assembly LH.
(d) Connect the cable to the negative (-) auxiliary battery terminal.
for M20A-FKS: Click here
for 2ZR-FXE: Click here
(e) Temporarily install the front seat assembly LH with the 4 bolts.
(f) Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.
|
(g) Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly LH. Torque: 37 N·m {377 kgf·cm, 27 ft·lbf} NOTICE: Tighten the bolts in the order shown in the illustration. |
|
(h) Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the foremost position.
|
(i) Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly LH. Torque: 37 N·m {377 kgf·cm, 27 ft·lbf} NOTICE: Tighten the bolts in the order shown in the illustration. |
|
2. INSTALL INNER SEAT TRACK BRACKET COVER LH
|
(a) Engage the 2 claws and guide to install the inner seat track bracket cover LH. |
|
3. INSTALL OUTER SEAT TRACK COVER LH
|
(a) Engage the 2 claws and guide to install the outer seat track cover LH. |
|
4. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH
(a) Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.
|
(b) Engage the 2 claws to install the front inner seat track bracket cover LH. |
|
5. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH
|
(a) Engage the 2 claws to install the front outer seat track bracket cover LH. |
|
6. INSTALL FRONT SEAT HEADREST ASSEMBLY
(a) Install the front seat headrest assembly to the front seat assembly LH.
7. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
8. INSPECT FRONT SEAT ASSEMBLY
Click here
9. CHECK SEAT HEATER (w/ Seat Heater System)
Click here
10. INSPECT SRS WARNING LIGHT
for TMC Made: Click here
|
|