- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000028W6O |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: AUDIO / VIDEO: RADIO ANTENNA CORD (for Hatchback): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
2. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here
3. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY
(a) w/ Navigation Antenna:
|
(1) Disconnect the connector and disengage the 2 claws. |
|
(2) Disengage the clamp.
(b) w/ Manual (SOS) Switch
(1) Disengage each clamp and remove the antenna cord sub-assembly.
|
*A |
w/ Manual (SOS) Switch |
- |
- |
4. REMOVE ROOF HEADLINING ASSEMBLY
Click here
5. REMOVE NO. 1 ROOF SILENCER PAD
Click here
6. REMOVE NO. 2 ROOF SILENCER PAD
Click here
7. REMOVE NO. 3 ROOF SILENCER PAD
Click here
8. REMOVE ANTENNA CORD SUB-ASSEMBLY
(a) for Normal Roof:
(1) Remove the adhesive tape from the roof headlining assembly.
|
Adhesive Tape |
- |
- |
(2) Remove the antenna cord sub-assembly from the roof headlining assembly.
(b) for Carbon Fiber Reinforced Plastic Roof:
(1) Remove the antenna cord sub-assembly from the roof headlining assembly.
|
|
Adhesive Tape |
- |
- |
(2) Remove the antenna cord sub-assembly from the roof headlining assembly.
9. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER
Click here
10. REMOVE ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the washer hose. HINT: Use a container to collect the windshield washer fluid. |
|
(b) Disengage the 2 clamps.
(c) for Normal Roof:
|
(1) Disconnect the connector. |
|
(2) Disengage the 4 clamps.
(d) for Carbon Fiber Reinforced Plastic Roof:
|
(1) Disconnect the connector. |
|
(2) Remove the bolt.
(3) Disengage the 4 clamps.
|
(e) Disconnect the washer hose. HINT: Use a container to collect the windshield washer fluid. |
|
|
(f) Disengage the 8 claws to separate the 2 grommets. |
|
(g) Remove the antenna cord sub-assembly.
|
|