Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000028W6O |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: AUDIO / VIDEO: RADIO ANTENNA CORD (for Hatchback): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Necessary Procedures
|
Link
|
Front Camera System
|
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
|
|
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Necessary Procedures
|
Link
|
Front Camera System
|
-
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
-
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
|
|
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Necessary Procedures
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
2. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here
3. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY
(a) w/ Navigation Antenna:
(1) Disconnect the connector and disengage the 2 claws.
|
|
(2) Disengage the clamp.
(b) w/ Manual (SOS) Switch
(1) Disengage each clamp and remove the antenna cord sub-assembly.
*A
|
w/ Manual (SOS) Switch
|
-
|
-
|
4. REMOVE ROOF HEADLINING ASSEMBLY
Click here
5. REMOVE NO. 1 ROOF SILENCER PAD
Click here
6. REMOVE NO. 2 ROOF SILENCER PAD
Click here
7. REMOVE NO. 3 ROOF SILENCER PAD
Click here
8. REMOVE ANTENNA CORD SUB-ASSEMBLY
(a) for Normal Roof:
(1) Remove the adhesive tape from the roof headlining assembly.
|
Adhesive Tape
|
-
|
-
|
(2) Remove the antenna cord sub-assembly from the roof headlining assembly.
(b) for Carbon Fiber Reinforced Plastic Roof:
(1) Remove the antenna cord sub-assembly from the roof headlining assembly.
|
Adhesive Tape
|
-
|
-
|
(2) Remove the antenna cord sub-assembly from the roof headlining assembly.
9. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER
Click here
10. REMOVE ANTENNA CORD SUB-ASSEMBLY
(a) Disconnect the washer hose.
HINT:
Use a container to collect the windshield washer fluid.
|
|
(b) Disengage the 2 clamps.
(c) for Normal Roof:
(1) Disconnect the connector.
|
|
(2) Disengage the 4 clamps.
(d) for Carbon Fiber Reinforced Plastic Roof:
(1) Disconnect the connector.
|
|
(2) Remove the bolt.
(3) Disengage the 4 clamps.
(e) Disconnect the washer hose.
HINT:
Use a container to collect the windshield washer fluid.
|
|
(f) Disengage the 8 claws to separate the 2 grommets.
|
|
(g) Remove the antenna cord sub-assembly.
|