Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM1000000028VAF
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [11/2022 -           ]
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for 12.3 Inch Display): Fuel Receiver Gauge Malfunction; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]

Fuel Receiver Gauge Malfunction

DESCRIPTION

FUEL RECEIVER GAUGE DESCRIPTION

  • The combination meter assembly receives the fuel level signal via direct line from the fuel sender gauge assembly and No. 2 fuel sender gauge assembly and the fuel consumption signal from the ECM via CAN communication, then calculates the fuel level in the fuel tank and displays the calculated value on the fuel receiver gauge.

FUEL RECEIVER GAUGE CONTROL

(a) During normal driving:

  • During driving, the value of the fuel receiver gauge is updated based on the reduction in the fuel level. The reduction is calculated by deducting the value calculated based on the fuel consumption signal sent by the ECM from the value calculated based on the signal sent by the fuel sender gauge assembly and No. 2 fuel sender gauge assembly.

(b) During refueling:

  • As the fuel level in the fuel tank increases during refilling, the output value of the fuel sender gauge assembly and No. 2 fuel sender gauge assembly changes. When the combination meter assembly detects a change in the output value of the fuel sender gauge assembly and No. 2 fuel sender gauge assembly of a certain value or more, it determines that fuel is being added and calculates the added amount. This control is called refueling judgment and the fuel receiver gauge display is updated in accordance with the fuel level calculated based on the refueling judgment.

PRECAUTION FOR REFUELING

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for 12.3 Inch Display): PRECAUTION

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
  • When replacing the combination meter assembly, update the ECU security key.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: UPDATE ECU SECURITY KEY

  • Before preforming this procedure, check for Meter / Gauge System DTC B150013 or B150113 which is stored if an open or short in the circuit is detected. If DTC B150013 or B150113 is output, perform troubleshooting and repairs as necessary.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for 12.3 Inch Display): B150013,B150113; Fuel Sender Circuit Open

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

  • To prevent the key from being locked in the vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Check if CAN communication DTCs are output.

Click here 2023 MY Corolla Corolla Hatchback GR Corolla [11/2022 - 03/2023]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM 2023 MY Corolla Corolla Hatchback GR Corolla [03/2023 - 08/2023]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM 2024 - 2025 MY Corolla Corolla Hatchback GR Corolla [08/2023 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO CAN COMMUNICATION SYSTEM 2023 MY Corolla Corolla Hatchback GR Corolla [11/2022 - 08/2023]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING 2024 - 2025 MY Corolla Corolla Hatchback GR Corolla [08/2023 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING

A

2.

CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

(a) Check if electronically controlled brake system DTCs are output.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM

A

3.

CHECK SYMPTOMS

(a) Check the problem symptoms.

Result

Proceed to

Malfunction occurs when adding fuel (Even when refueled, display value does not increase)

A

Malfunction occurs when adding fuel (When refueled, display value increase is slow)

B

Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.)

(The problem symptom recurs)

C

Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.)

(The problem symptom does not recur)

D
B

GO TO STEP 5

C

GO TO STEP 6

D

GO TO STEP 8

A

4.

MANUALLY UPDATE FUEL RECEIVER GAUGE

(a) Perform a manual update of the fuel receiver gauge.

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for 12.3 Inch Display): PRECAUTION

(b) Check that the display value of the fuel receiver gauge has changed.

Result

Proceed to

Display value of the fuel receiver gauge has changed

A

Display value of the fuel receiver gauge has not changed

B
A

END (TEMPORARY ERROR DUE TO FUEL RECEIVER GAUGE CHARACTERISTICS)

HINT:

It is suspected that the indicated value of the fuel receiver gauge did not automatically update due to the following reasons:

  • The amount of added fuel was less than the refueling judgement amount.
  • Refueling was performed in a range for which detection is not possible (indicated value of fuel receiver gauge was near E, F)

B

GO TO STEP 5

5.

CHECK FUEL RECEIVER GAUGE (OPERATION BY ADDING FUEL)

NOTICE:

As it is necessary to add more than a certain amount of fuel to the fuel tank, if the fuel level is near full, perform the following procedure then proceed to step (a). If the fuel tank is not near full, proceed to step (a) without performing the following procedure.

  1. Turn the ignition switch off.
  2. Remove 15 liters (15.9 US qts, 13.2 Imp. qts) or more of fuel from the fuel tank.
  3. Turn the ignition switch to ON.
  4. Wait 6 minutes or more.
  5. Confirm that the fuel receiver gauge indicates a value in accordance with the removed amount of fuel.

(a) Record the fuel receiver gauge reading.

(b) Turn the ignition switch off.

(c) Disconnect the cable from the negative (-) auxiliary battery terminal.

HINT:

This resets the current fuel level information stored by the combination meter assembly.

(d) Wait 2 minutes or more.

(e) Connect the cable to the negative (-) auxiliary battery terminal.

(f) Turn the ignition switch to ON.

(g) Drive the vehicle at 2 km/h (1 mph) or more, and then stop the vehicle on a flat surface.

(h) Turn the ignition switch off.

(i) Wait 30 seconds or more.

(j) Add the following amount of fuel or more.

  • 6.0 liters (6.3 US qts, 5.3 Imp. qts)

(k) Turn the ignition switch to ON.

(l) Check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.

NOTICE:

After turning the ignition switch to ON, it may take approximately 30 seconds until the fuel receiver gauge indicates the determined value.

Result

Proceed to

Fuel receiver gauge reading increases in proportion to the amount of fuel added

A

Fuel receiver gauge reading does not change even when fuel is added

B
A

GO TO STEP 8

B

REPLACE COMBINATION METER ASSEMBLY

6.

CHECK FOR DTC (SFI SYSTEM)

(a) Check if SFI system DTCs are output.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO SFI SYSTEM

A

7.

CHECK FUEL RECEIVER GAUGE

(a) Record the fuel receiver gauge reading.

(b) Turn the ignition switch off.

(c) Disconnect the cable from the negative (-) auxiliary battery terminal.

HINT:

This resets the current fuel level information stored by the combination meter assembly.

(d) Wait 2 minutes or more.

(e) Connect the cable to the negative (-) auxiliary battery terminal.

(f) Wait 30 seconds or more.

(g) Turn the ignition switch to ON.

(h) Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank.

NOTICE:

After turning the ignition switch to ON, it may take approximately 30 seconds until the fuel receiver gauge indicates the determined value.

Result

Proceed to

Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank

A

Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank

B
A

GO TO STEP 8

B

REPLACE COMBINATION METER ASSEMBLY

8.

INSPECT FUEL TANK SUB-ASSEMBLY

HINT:

Inspect the fuel tank sub-assembly, fuel sender gauge assembly and No. 2 fuel sender gauge assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.

(a) Visually check the fuel tank sub-assembly for any abnormalities.

(b) Check if there is an excessive amount of foreign matter in the fuel tank sub-assembly.

(c) Visually check the fuel sender gauge assembly and No. 2 fuel sender gauge assembly for damage and confirm that it operates correctly.

(d) Check the installation condition of the fuel tank sub-assembly, fuel sender gauge assembly and No. 2 fuel sender gauge assembly.

Result

Proceed to

Normal

A

Appearance of the fuel tank sub-assembly is abnormal

B

There is an excessive amount of foreign matter in the fuel tank sub-assembly

C

The fuel sender gauge assembly or No. 2 fuel sender gauge assembly is visually damaged or does not operate correctly

D

The fuel tank sub-assembly, fuel sender gauge assembly or No. 2 fuel sender gauge assembly is not installed correctly

E
A

USE SIMULATION METHOD TO CHECK

B

REPLACE FUEL TANK SUB-ASSEMBLY

C

CLEAN INSIDE OF FUEL TANK SUB-ASSEMBLY
D

REPLACE FUEL SENDER GAUGE ASSEMBLY OR NO. 2 FUEL SENDER GAUGE ASSEMBLY

E

INSTALL FUEL TANK SUB-ASSEMBLY, FUEL SENDER GAUGE ASSEMBLY OR NO. 2 FUEL SENDER GAUGE ASSEMBLY CORRECTLY