Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM1000000028QLO
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [11/2022 -           ]
Title: PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model): Electric Parking Brake does not Operate; 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [11/2022 -        ]

Electric Parking Brake does not Operate

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Check if CAN communication system DTCs are output.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO CAN COMMUNICATION SYSTEM 2023 MY Corolla Corolla Hatchback GR Corolla [11/2022 - 08/2023]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING 2024 - 2025 MY Corolla Corolla Hatchback GR Corolla [08/2023 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING

A

2.

VEHICLE OPERATION CHECK

(a) With the wheels not contacting the ground, check the condition of the rear wheels when the electric parking brake is operating and not operating.

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; PARKING BRAKE: ELECTRIC PARKING BRAKE ACTUATOR: ON-VEHICLE INSPECTION

Result

Proceed to

Lock and release operation is normal and parking brake indicator light turns off or blinks (red)

A

Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation

B

Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red)

C
B

INSPECT REAR BRAKE
C

GO TO STEP 4

A

3.

INSPECT COMBINATION METER ASSEMBLY

(a) Perform the Active Test of the combination meter assembly using the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Park Warning

(b) Check the combination meter assembly.

OK:

Parking brake indicator light (red) turns on or off in accordance with Techstream operation.

OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

GO TO METER / GAUGE SYSTEM

4.

CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)

(a) Turn the engine switch off.

(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A51-30 (+BS) - Body ground

Always

11 to 14 V

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Actuator Assembly))
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

5.

CHECK HARNESS AND CONNECTOR (IG1 TERMINAL VOLTAGE)

(a) Turn the engine switch off.

(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A51-36 (IGR) - Body ground

Engine switch on (IG)

11 to 14 V

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Actuator Assembly))
OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR