Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM1000000028M5M
Model Year Start: 2023 Model: Corolla Hatchback Prod Date Range: [11/2022 - 03/2023]
Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: VC Output Circuit; 2023 MY Corolla Corolla Hatchback [11/2022 - 03/2023]

VC Output Circuit

DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

  • For the circuit diagram of the ECM power source refer to the ECM power source circuit.

    Click here 2023 MY Corolla Corolla Hatchback [11/2022 - 03/2023]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: ECM Power Source Circuit+

  • VC Output Circuit

CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

A

2.

CHECK EFI NO. 2 FUSE VOLTAGE

*1

NO.1 Engine Room Relay Block and NO.1 Junction Block Assembly

*2

EFI NO. 2 Fuse

(a) Turn the ignition switch to ON.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

1 (EFI NO. 2 fuse) - Body ground

Ignition switch ON

11 to 14 V

HINT:

  • Check the fuse with it installed to the No. 1 engine room relay block and No. 1 junction block assembly.
  • If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
NG

GO TO ECM POWER SOURCE CIRCUIT

OK

3.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (THROTTLE POSITION SENSOR)

(a) Disconnect the throttle body with motor assembly connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click here 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 -        ]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

A

4.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

(a) Disconnect the accelerator pedal sensor assembly connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

A

5.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (CRANKSHAFT POSITION SENSOR)

(a) Disconnect the crankshaft position sensor connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

REPLACE CRANKSHAFT POSITION SENSOR

A

6.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

(a) Disconnect the camshaft position sensor (for intake camshaft) connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

A

7.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

(a) Disconnect the manifold absolute pressure sensor connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

A

8.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

(a) Disconnect the camshaft position sensor (for exhaust camshaft) connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

A

9.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (OIL PRESSURE AND TEMPERATURE SENSOR)

(a) Disconnect the oil pressure and temperature sensor connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

REPLACE OIL PRESSURE AND TEMPERATURE SENSOR

A

10.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

(a) Disconnect the fuel pressure sensor (for high pressure side) connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click here 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 -        ]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

A

11.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

(a) Disconnect the No. 2 fuel pressure sensor (for low pressure side) connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

HINT:

Perform "Inspection After Repair" after replacing the No. 2 fuel pressure sensor (for low pressure side).

Click here 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 -        ]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

B

REPLACE NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE)

A

12.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

(a) Disconnect the mass air flow meter sub-assembly connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click here 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 -        ]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

A

13.

CHECK CONNECTION BETWEEN TECHSTREAM AND ECM (CANISTER PUMP MODULE)

(a) Disconnect the canister pump module connector.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check the communication between the Techstream and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.

Result

Proceed to

Communication is not possible

A

Communication is possible

B

B

REPLACE CANISTER PUMP MODULE

w/ Canister Pump Module (for Double Wishbone Type Suspension): Click here 2023 - 2025 MY Corolla Corolla Hatchback [09/2022 -        ]; M20A-FKS (EMISSION CONTROL): CANISTER (w/ Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

w/ Canister Pump Module (for Torsion Beam Type Suspension): Click here 2023 - 2025 MY Corolla Corolla Hatchback [09/2022 -        ]; M20A-FKS (EMISSION CONTROL): CANISTER (w/ Canister Pump Module (for Torsion Beam Type Suspension)): REMOVAL

A

14.

CHECK HARNESS AND CONNECTOR

(a) Disconnect the throttle body with motor assembly connector.

(b) Disconnect the crankshaft position sensor connector.

(c) Disconnect the camshaft position sensor (for intake camshaft) connector.

(d) Disconnect the camshaft position sensor (for exhaust camshaft) connector.

(e) Disconnect the manifold absolute pressure sensor connector.

(f) Disconnect the oil pressure and temperature sensor connector.

(g) Disconnect the accelerator pedal sensor assembly connector.

(h) Disconnect the mass air flow meter sub-assembly connector.

(i) Disconnect the fuel pressure sensor (for high pressure side) connector.

(j) Disconnect the No. 2 fuel pressure sensor (for low pressure side) connector.

(k) Disconnect the canister pump module connector.

(l) Disconnect the ECM connectors.

(m) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

C76-109 (VCTA) - Body ground

Always

10 kΩ or higher

C76-116 (VCNE) - Body ground

Always

10 kΩ or higher

C76-88 (VCV1) - Body ground

Always

10 kΩ or higher

C76-113 (VCE1) - Body ground

Always

10 kΩ or higher

C76-121 (VCPM) - Body ground

Always

10 kΩ or higher

C76-99 (VCPE) - Body ground

Always

10 kΩ or higher

A47-57 (VCPA) - Body ground

Always

10 kΩ or higher

A47-60 (VCP2) - Body ground

Always

10 kΩ or higher

C76-78 (VCVG) - Body ground

Always

10 kΩ or higher

C76-98 (VCPR) - Body ground

Always

10 kΩ or higher

C76-84 (VCPF) - Body ground

Always

10 kΩ or higher

A47-48 (VCPP) - Body ground

Always

10 kΩ or higher

(n) Remove the EFI-MAIN NO. 2 relay, EFI-MAIN NO. 3 relay and VVT relay from the No. 1 engine room relay block and No. 1 junction block assembly.

HINT:

Remove the EFI-MAIN NO. 2, EFI-MAIN NO. 3 relay and VVT relay connected between the checked terminals as the coil inside the relay influences the measurement value.

(o) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A47-9 (+B) - 1 (EFI NO. 2 fuse)

Always

Below 1 Ω

A47-35 (+B2) - 1 (EFI NO. 2 fuse)

Always

Below 1 Ω

A47-9 (+B) - Body ground

Always

10 kΩ or higher

A47-35 (+B2) - Body ground

Always

10 kΩ or higher

OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR