Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000028LVQ |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: NETWORKING: LIN COMMUNICATION SYSTEM: B278987; ID-BOX Missing Message; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] |
DTC
|
B278987
|
ID-BOX Missing Message
|
DESCRIPTION
This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
DTC Output from
|
B278987
|
ID-BOX Missing Message
|
No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.
|
-
Certification ECU (smart key ECU assembly)
-
ID code box (immobiliser code ECU)
-
Wire harness or connector
|
Smart Key
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Inspect the fuses for circuits related to this system before performing the following procedure.
-
When using the GTS with the ignition switch off, perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins, and then select the vehicle model manually.
Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key (CAN). While using the GTS, periodically perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
-
If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to Registration.
for HV Model: Click here
for Gasoline Model: Click here
PROCEDURE
1.
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))
|
(a) Disconnect the I167 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the I20 ID code box (immobiliser code ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I167-8 (LIN) - I20-2 (LIN1)
|
Ignition switch off
|
Below 1 Ω
|
I167-8 (LIN) or I20-2 (LIN1) - Body ground
|
Ignition switch off
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - AUXILIARY BATTERY AND BODY GROUND)
|
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I20-1 (+B) - Body ground
|
Always*1
Ignition switch off*2
|
11 to 14 V
|
-
*1: for Gasoline Model
-
*2: for HV Model
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I20-5 (GND) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
|
(a) Replace the ID code box (immobiliser code ECU).
Click here
NEXT
|
|
|
4.
|
REGISTER ECU CODE REGISTRATION
|
(a) Register the recognition codes in the ECUs.
for HV Model: Click here
for Gasoline Model: Click here
NEXT
|
|
|
(a) Clear the DTCs.
Body Electrical > Smart Key > Clear DTCs
(b) Recheck for DTCs.
Body Electrical > Smart Key > Trouble Codes
OK:
DTC B278987 is not output.
OK |
|
END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)
|
|