SLIDING ROOF / CONVERTIBLE: SLIDING ROOF SYSTEM: OPERATION CHECK; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022

NOTICE:

Make sure that initialization has been completed before performing this inspection.
Click here
The sliding roof auto operation can be customized. Make sure that the auto operation customize setting is set to ON.
Click here

When a switch is pressed for 0.3 seconds or less, the sliding roof will move but auto operation will not operate.

(b) When the sliding roof is fully closed, press the OPEN switch for 0.3 seconds or more. Check that the sliding roof automatically slides until it reaches the comfort stop position.

(c) When the sliding roof is in the comfort stop position, press the OPEN switch again for 0.3 seconds or more. Check that the sliding roof automatically slides until it is fully opened.

(d) When the sliding roof is fully open, press the CLOSE switch for 0.3 seconds or more. Check that the sliding roof automatically slides until it is fully closed.

(e) When the sliding roof is fully closed, press the UP switch for 0.3 seconds or more. Check that the sliding roof automatically tilts up until it is fully tilted upward.

(f) When the sliding roof is fully tilted up, press the DOWN switch for 0.3 seconds or more. Check that the sliding roof automatically tilts down until it is fully tilted downward.

(g) When the auto operation function is operating, check that pressing any of the switches on the sliding roof switch (map light assembly) stops the sliding roof operation.

Make sure that initialization has been completed before performing this inspection.

(a) Turn the ignition switch from ON to off and check that the sliding roof can be operated. Then open the driver or front passenger door once and check that the sliding roof cannot be operated.

(b) Turn the ignition switch from ON to off and wait for approximately 45 seconds. Check that the sliding roof cannot be operated.

CAUTION:

Do not use a part of your body, for example, your hand, to check the jam protection function.
Do not allow anything to become caught in the sliding roof by accident while performing this inspection.
Perform the inspection from the inside of the vehicle.

NOTICE:

To avoid damaging the roof, do not use a hard object, such as a hammer, when performing this inspection.
Make sure that initialization has been completed before performing this inspection.
Click here
The jam protection function does not operate when the sliding roof is close to the fully closed position.

(a) When the slide close function is operating and an object is caught between the vehicle body and sliding roof glass sub-assembly, check that the sliding roof opens a distance of 218 mm (8.58 in.) from the point of contact with the object, or opens fully if an opening distance of 218 mm (8.58 in.) is not available.

(b) When the tilt down function is operating and an object is caught between the vehicle body and the sliding roof glass sub-assembly, check that the sliding roof tilts up fully.

Make sure that no one is near the vehicle while performing this inspection. Also be careful not to let any part of your body, such as your hand, get caught in the sliding roof by accident while performing this inspection.

NOTICE:

Make sure that initialization has been completed before performing this inspection.
Click here
The sliding roof key-linked function can be customized. Make sure that the key-linked function customize settings are set to ON.
Click here

HINT:

This function is linked with the power window key-linked function.
The sliding roof key-linked function can be customized to perform either the sliding operation or tilting operation.

(2) Insert the mechanical key into the driver door key cylinder and turn the mechanical key to the unlock position for approximately 2.5 seconds or more. Check that slide open/tilt up operation occurs. Then release the mechanical key and check that the sliding roof stops moving.

(1) Open the sliding roof by using the sliding roof switch (map light assembly).

(3) Insert the mechanical key into the driver door key cylinder, and turn the mechanical key to the lock position for approximately 2.5 seconds or more. Check that the slide close/tilt down operation occurs. Then release the mechanical key and check that the sliding roof stops moving.

NOTICE:

Make sure that initialization has been completed before performing this inspection.
Click here
The sliding roof wireless transmitter-linked function can be customized. Make sure that the wireless transmitter-linked function customize settings are set to ON.
Click here

HINT:

This function is linked with the power window wireless transmitter-linked function.
The wireless transmitter-linked function can be customized to perform either the sliding operation or tilting operation.

(2) Press and hold the unlock switch of the wireless transmitter for approximately 4 seconds or more and check that the slide open/tilt up operation occurs. Then release the unlock switch and check that the sliding roof stops moving.

(3) Hold down the wireless transmitter lock switch of the wireless transmitter for approximately 4 seconds or more and check that the slide close/tilt down operation occurs. Then release the lock switch and check that the sliding roof stops moving.*

NOTICE:

Make sure that initialization has been completed before performing this inspection.
Click here
The sliding roof open warning can be customized. Make sure that the sliding roof open warning customize setting is set to ON.
Click here

(a) Open the sliding roof by using the sliding roof switch (map light assembly).

(b) Turn the ignition switch off, open the driver door and check that the warning buzzer in the combination meter assembly sounds once and a warning message is displayed on the multi-information display in the combination meter assembly.