G16E-GTS (ENGINE MECHANICAL): CYLINDER HEAD GASKET: REMOVAL; 2023 - 2025 MY GR Corolla [11/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM1000000028LKO
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [11/2022 - ]
Title: G16E-GTS (ENGINE MECHANICAL): CYLINDER HEAD GASKET: REMOVAL; 2023 - 2025 MY GR Corolla [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*1:w/ Steering Lock Function
Replacement of ECM	Perform Vehicle Identification Number (VIN) or frame number registration	MIL illuminates
	ECU configuration	-
	Update ECU security key	Vehicle Control History (RoB) are stored
	Heavy Knock History	-
	ECU communication ID registration (Immobiliser system)	Engine start function
	Code registration (Smart Key System (for Gasoline Model, Start Function))	Wireless Door Lock Control System (for Gasoline Model with Smart Key System) Smart Key System (for Gasoline Model, Entry Function) Smart Key System (for Gasoline Model, Start Function) Steering lock function*1
Replacement of throttle body with motor assembly Cleaning the deposits from the throttle body with motor assembly Replacement of engine assembly Replacement of cylinder head sub-assembly Replacement of camshaft (for intake or exhaust camshaft) Replacement of camshaft timing gear assembly Replacement of camshaft timing exhaust gear assembly Replacement of fuel pump assembly (for high pressure side) Replacement of fuel pressure sensor (for high pressure side) Replacement of air fuel ratio sensor Replacement of engine coolant temperature sensor Replacement of spark plug Replacement of ignition coil assembly Replacement of knock control sensor Replacement of turbocharger sub-assembly Gas leaks from exhaust system is repaired	Inspection After Repair	Poor idle, etc. Engine start function, etc.
Front wheel alignment adjustment	Perform "Reset Memory" Perform "Calibration"	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates
Tire	ECU Data Initialization (When performing tire replacement after RoB code X2104 is output)	Active Torque Split AWD System

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Power door lock control system Back door opener	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

PROCEDURE

1. REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Click here

2. REMOVE NO. 1 CAMSHAFT BEARING CAP

Click here

3. REMOVE NO. 5 CAMSHAFT BEARING CAP

Click here

4. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Click here

5. REMOVE VALVE LASH ADJUSTER ASSEMBLY

Click here

6. REMOVE VALVE STEM CAP

Click here

7. REMOVE CYLINDER HEAD SUB-ASSEMBLY

Click here

8. REMOVE CYLINDER HEAD GASKET

(a) Remove the cylinder head gasket from the cylinder block sub-assembly.

9. INSPECT CYLINDER HEAD SET BOLT

Click here

10. INSPECT CYLINDER HEAD SUB-ASSEMBLY

Click here