Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000028K8P
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [11/2022 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function): DATA LIST / ACTIVE TEST; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]

DATA LIST / ACTIVE TEST

NOTICE:

  • In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  • When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins.

    Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Start Key(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • When performing an inspection, make sure that "ACC Customize" is set to "ON" using the multi-display.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function): CUSTOMIZE PARAMETERS

  • When "ACC Customize" is set to "ON" (ACC supply power enabled), the certification ECU (smart key ECU assembly) controls the ACC relay on and off. When "ACC Customize" is set to "OFF" (ACC supply power disabled), the certification ECU (smart key ECU assembly) and radio and display receiver assembly control the ACC relay on and off.

    Therefore, inspection conditions and results may differ depending on whether "ACC customize" is set to ON or OFF when inspecting the Data List.

DATA LIST

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the GTS on.

(d) Enter the following menus: Body Electrical / Smart Key, Main Body or Power Source Control / Data List.

(e) Read the Data List according to the display on the GTS.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Driver Side Unlock Sensor

Driver door touch sensor (unlock sensor)*1

OFF or ON

OFF: Driver door touch sensor (unlock sensor) not touched

ON: Driver door touch sensor (unlock sensor) touched
  • Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  • Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.

Passenger Side Unlock Sensor

Front passenger door touch sensor (unlock sensor)*1

OFF or ON

OFF: Front passenger door touch sensor (unlock sensor) not touched

ON: Front passenger door touch sensor (unlock sensor) touched
  • Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  • Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.

Driver Side Lock Sensor

Driver door touch sensor (lock sensor)*1

OFF or ON

OFF: Driver door touch sensor (lock sensor) not touched

ON: Driver door touch sensor (lock sensor) touched
  • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.

Passenger Side Lock Sensor

Front passenger door touch sensor (lock sensor)*1

OFF or ON

OFF: Front passenger door touch sensor (lock sensor) not touched

ON: Front passenger door touch sensor (lock sensor) touched
  • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.

Trunk Lid/Back Door Lock Switch

except Sedan:

  • Back door opener switch sub-assembly (lock switch)

OFF or ON

OFF: Back door opener switch sub-assembly (lock switch) not pressed

ON: Back door opener switch sub-assembly (lock switch) pressed
  • Displays whether the back door opener switch sub-assembly (lock switch) is on or off.
  • Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.

Trunk Lid/Back Door Unlock Switch

except Sedan:

  • Back door opener switch sub-assembly (open switch)

for Sedan:

  • Luggage electrical key switch

OFF or ON

except Sedan:

  • OFF: Back door opener switch sub-assembly (open switch) not pressed
  • ON: Back door opener switch sub-assembly (open switch) pressed

except Sedan:

  • OFF: Luggage electrical key switch not pressed
  • ON: Luggage electrical key switch pressed

except Sedan:

  • Displays whether the back door opener switch sub-assembly (unlock switch) is on or off.
  • Use this Data List item to help determine if there is a switch malfunction when the entry back door open function does not operate.

for Sedan:

  • Displays whether the luggage electrical key switch is on or off.
  • Use this Data List item to help determine if there is a switch malfunction when the entry luggage compartment door open function does not operate.

Electronic Key No Response

Communication response

No or Yes

No: Communication normal

Yes: Communication malfunction

The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the engine switch is pressed, etc., "Yes" is displayed for "Electronic Key No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Electronic Key No Response" in the Data List.)

Other potential causes:

  • An electrical key transmitter sub-assembly from a different vehicle is being used.
  • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.

Unmatched Response Code or Form

Code format (incorrect or correct)

No or Yes

No: Communication normal

Yes: Communication malfunction

There is an error in the data sent from the electrical key transmitter sub-assembly (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatched Response Code or Form", "Electronic Key No Response", "ID Code Difference" and "C Code Difference" in the Data List).

Other potential causes:

  • An electrical key transmitter sub-assembly from a different manufacturer is being used.
  • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.

Key Low Battery

Transmitter battery depleted

No or Yes

No: Transmitter battery not depleted

Yes: Transmitter battery depleted

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).

C Code Difference

Challenge code (incorrect or correct)

No or Yes

No: Communication normal

Yes: Communication malfunction

The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatched Response Code or Form", "Electronic Key No Response", "ID Code Difference" and "C Code Difference" in the Data List).

Other potential causes:

  • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.

Out of Collation Area

Detection area (incorrect or correct)

No or Yes

No: Communication normal

Yes: Communication malfunction

-

LF Wave Change

LF wave change (incorrect or correct)

No or Yes

No: Communication normal

Yes: Communication malfunction

-

B Code Difference

B code mismatch

No or Yes

No: Communication normal

Yes: Communication malfunction

-

B Code Registered

B code registration status

No or Yes

No: B code is not registered properly

Yes: B code is registered properly

-

Vehicle ID Difference (Key Registration)

Status of vehicle ID (key registration)

No or Yes

No: Vehicle ID normal (key registration)

Yes: Vehicle ID malfunction (key registration)

-

Electrical Key 4 Low Battery History

Low battery transmission history (electronic key 4)

OFF or ON

OFF: Transmitter battery not depleted

ON: Transmitter battery depleted

-

Electrical Key 3 Low Battery History

Low battery transmission history (electronic key 3)

OFF or ON

OFF: Transmitter battery not depleted

ON: Transmitter battery depleted

-

Electrical Key 2 Low Battery History

Low battery transmission history (electronic key 2)

OFF or ON

OFF: Transmitter battery not depleted

ON: Transmitter battery depleted

-

Electrical Key 1 Low Battery History

Low battery transmission history (electronic key 1)

OFF or ON

OFF: Transmitter battery not depleted

ON: Transmitter battery depleted

-

10 Minutes Power Save Counter

Number of times power saving control is activated due to electrical key transmitter sub-assembly being in detection area for 10 minutes or more

0 to 255

Within range of 0 to 255

If the electrical key transmitter sub-assembly is in a vehicle exterior detection area, communication is frequently performed between the vehicle and electrical key transmitter sub-assembly, resulting in an increase in transmitter battery power consumption. To prevent the transmitter battery from becoming fully depleted, if the electrical key transmitter sub-assembly is left in the detection area for 10 minutes or more, the smart key system automatically deactivates the exterior detection area the electrical key transmitter sub-assembly is in. If the doors are locked/unlocked with a wireless operation or by the mechanical key, the system resumes operation.

5 Days Power Save Counter

Number of times power saving control 1 (vehicle exterior periodic signal transmission stop) is activated due to hybrid control system*2 or engine*3 not being started for 5 days or more

0 to 255

Within range of 0 to 255

-

14 Days Power Save Counter

Number of times power saving control 2 (lock/unlock sensor of front door outside handle assembly of front passenger door disabled) is activated due to hybrid control system*2 or engine*3 not being started for 14 days or more

0 to 255

Within range of 0 to 255

-

ID Code Difference

Wireless ID code (incorrect or correct)

No or Yes

No: Communication normal

Yes: Communication malfunction

The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "Response ID Code Difference" in the Data List.)

Other potential causes:

  • An electrical key transmitter sub-assembly from a different vehicle is being used.
  • A communication error due to external noise (RF).
  • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.

Rolling Code Difference

Rolling code (incorrect or correct)

No or Yes

No: Communication normal

Yes: Communication malfunction

The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different

Other potential causes:

  • An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the radio waves cannot reach the vehicle.
  • A communication error due to external noise (RF).
  • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.

Wireless Certification Signal Encryption

Wireless signal encryption support

Without or With

Without: Wireless signal encryption not supported

With: Wireless signal encryption supported

-

Driver Side Door Oscillators Circuit Short

Short in driver door electrical key antenna circuit

OFF or ON

OFF: Driver door electrical key antenna circuit is normal

ON: Driver door electrical key antenna circuit is abnormal

-

Front P Side Door Oscillators Circuit Short

Short in front passenger door electrical key antenna circuit

OFF or ON

OFF: Front passenger door electrical key antenna circuit is normal

ON: Front passenger door electrical key antenna circuit is abnormal

-

D Side Door Oscillators Circuit Short History

Short in driver door electrical key antenna circuit (history)

OFF or ON

OFF: Driver door electrical key antenna circuit was normal

ON: Driver door electrical key antenna circuit was abnormal

-

Fr P Side Door Oscillators Circuit Short History

Short in front passenger door electrical key antenna circuit (history)

OFF or ON

OFF: Front passenger door electrical key antenna circuit was normal

ON: Front passenger door electrical key antenna circuit was abnormal

-

B Code Registration Error History

B code registration status (history)

OFF or ON

OFF: B code is registered properly

ON: B code is not registered properly

-

Number of Registered Key Codes

Number of registered electrical key transmitter sub-assemblies

0 to 4

Number of registered electrical key transmitter sub-assemblies

Up to 4 electrical key transmitter sub-assemblies can be registered.

Ignition Available Area Setting (Trunk Lid Type)

for Sedan:

  • Ignition available area

Normal or Short

Customize setting displayed

-

Ignition Available Area Setting (Back Door Type)

except Sedan:

  • Ignition available area

Fr+Rr+BD

Customize setting displayed

-

Park Wait Time Adjust

Parking wait time

0.5sec, 1.5sec, 2.5sec or 5sec

Customize setting displayed

-

Door Unlock Sensor Touch Time Adjust

Function that sets the length of time the unlock sensor on the door outside handle assembly (for driver door) must be touched to unlock all of the doors state

OFF, Short, Middle or Long

Customize setting displayed

-

Trunk Lid Open Mode Function

except Sedan:

  • Trunk lid open mode

OFF or ON

Customize setting displayed

-

Key Low Battery Warning Function

Low transmitter battery warning

OFF or ON

Customize setting displayed

-

Key Left in Vehicle Alarm Function

Key left in vehicle buzzer

OFF or ON

Customize setting displayed

-

Forget to Turn IG OFF Alarm Function

Forget to turn ignition switch off alarm

OFF or ON

Customize setting displayed

-

Start Indicator Function

Key indicator display

OFF or ON

Customize setting displayed

-

Auto Entry Cancel Setting

Entry and start system function

OFF or ON

Customize setting displayed

-

Touch Activation Over Threshold

Consecutive entry lock operation

Active or Not Active

Customize setting displayed

-

Start Switch Light Function

Power switch*2 or engine switch*3 blink function

OFF or ON

Customize setting displayed

-

Power Saving Wait Time (Out of Entry Range)

Configuration of battery life extension support

Normal or Short

Customize setting displayed

-

Auto Entry Cancel 2 Setting

2 touch entry unlock function

OFF or ON

Customize setting displayed

-
  • *1: Data from an actual vehicle provided for reference.
  • *2: for HV Model
  • *3: for Gasoline Model

HINT:

  • *1: With ignition switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors locked, the unlock sensor of the front door outside handle assembly is touched.
  • *2: Approximately 150 ms
  • *3: With ignition switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors unlocked, the lock sensor of the front door outside handle assembly is touched.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Position Switch Status

Front door RH unlock detection switch signal

Lock or Unlock

Lock: Front door RH locked

Unlock: Front door RH unlocked

-

FL Door Lock Position Switch Status

Front door LH unlock detection switch signal

Lock or Unlock

Lock: Front door LH locked

Unlock: Front door LH unlocked

-

RR Door Lock Position Switch Status

Rear door RH unlock detection switch signal

Lock or Unlock

Lock: Rear door RH locked

Unlock: Rear door RH unlocked

-

RL Door Lock Position Switch Status

Rear door LH unlock detection switch signal

Lock or Unlock

Lock: Rear door LH locked

Unlock: Rear door LH unlocked

-

FR Door Courtesy Switch Status

Front door RH courtesy light switch signal

Close or Open

Close: Front door RH closed

Open: Front door RH open

-

FL Door Courtesy Switch Status

Front door LH courtesy light switch signal

Close or Open

Close: Front door LH closed

Open: Front door LH open

-

RR Door Courtesy Switch Status

Rear door RH courtesy light switch

Close or Open

Close: Rear door RH closed

Open: Rear door RH open

-

RL Door Courtesy Switch Status

Rear door LH courtesy light switch

Close or Open

Close: Rear door LH closed

Open: Rear door LH open

-

Back Door Courtesy Switch Status

except Sedan

  • Back door courtesy light switch

Close or Open

Close: Back door closed

Open: Back door open

-

Luggage Courtesy Switch Status

for Sedan

  • Luggage compartment door courtesy light switch

Close or Open

Close: Luggage compartment door closed

Open: Luggage compartment door open

-

IGR Power

Ignition switch status

OFF or ON

OFF: Ignition switch off

ON: Ignition switch ON

-

Body Electrical > Power Source Control > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Power Supply Condition

Power supply state

OFF, ACC ON, IGR ON, IGP ON or Starter ON

OFF: Ignition switch off

ACC ON: Ignition switch ACC

IGR ON: Ignition switch ON

IGP ON: Ignition switch ON

Starter ON: Sending hybrid control system*1 or engine*2 start request signal

-
  • *1: for HV Model
  • *2: for Gasoline Model

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the GTS on.

(d) Enter the following menus: Body Electrical / Smart Key or Main Body / Active Test.

(e) Perform Active Test according to the display on the GTS.

Body Electrical > Smart Key > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Overhead Tuner Power Supply

Door control receiver

OFF/ON

-

Driver Seat Sensor Power Supply

Front door outside handle (for driver door)

OFF/ON

-

Passenger Seat Sensor Power Supply

Front door outside handle (for front passenger door)

OFF/ON

-

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Door Lock

Door lock motor

OFF/ON

-

Door Unlock

Door lock motor

OFF/ON

-

Trunk Lid / Back Door Open

except Sedan:

  • Back door lock motor

for Sedan:

  • Luggage compartment door lock motor

OFF/ON

-

Wireless Buzzer

Wireless door lock buzzer

OFF/ON

-