| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000028JQ0 |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: LIGHTING (EXT): LIGHTING SYSTEM: B124400; Light Sensor Circuit Malfunction; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] | ||
|
DTC |
B124400 |
Light Sensor Circuit Malfunction |
DESCRIPTION
The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
DTC Output from |
|---|---|---|---|---|
|
B124400 |
Light Sensor Circuit Malfunction |
Detection condition:
Malfunction status:
Malfunction duration:
|
|
Main Body |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
for HV Model: Click here
![2023 - 2025 MY Corolla Corolla HV [09/2022 - ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION](/t3Portal/stylegraphics/info.gif)
for Gasoline Model: Click here
PROCEDURE
|
1. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs
|
|
2. |
CHECK FOR DTC |
(a) Turn the ignition switch to ON.
(b) Wait 10 seconds or more.
(c) Check for DTCs.
Body Electrical > Main Body > Trouble Codes
OK:
DTC B124400 is not output.
| OK |
|
|
|
3. |
READ VALUE USING GTS |
(a) According to the display on the GTS, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:
(1) Cover the automatic light control sensor with an opaque object.
(2) Slowly move the opaque object to uncover and then cover the automatic light control sensor.
Body Electrical > Main Body > Data List
|
Tester Display |
Measurement Item |
Normal Condition |
Reference Value |
Diagnostic Note |
|---|---|---|---|---|
|
Light Sensor Illuminance |
Automatic light control sensor illuminance |
0 to 8191 lx or SensorFail |
Value is output according to ambient light level |
The displayed value is "0" when no light is detected. |
Body Electrical > Main Body > Data List
|
Tester Display |
|---|
|
Light Sensor Illuminance |
OK:
The value changes according to the amount the automatic light control sensor is covered.
| OK |
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
(a) Disconnect the h1 automatic light control sensor connector.
(b) Disconnect the I85 main body ECU (multiplex network body ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
h1-1 (CLTB) - I85-8 (CLTB) |
Always |
Below 1 Ω |
|
h1-4 (CLTS) - I85-20 (CLTS) |
Always |
Below 1 Ω |
|
h1-2 (CLTE) - I85-21 (CLTE) |
Always |
Below 1 Ω |
|
h1-1 (CLTB) or I85-8 (CLTB) - Body ground |
Always |
10 kΩ or higher |
|
h1-4 (CLTS) or I85-20 (CLTS) - Body ground |
Always |
10 kΩ or higher |
|
h1-2 (CLTE) or I85-21 (CLTE) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
|
*a |
Component with harness connected (Main Body ECU (Multiplex Network Body ECU)) |
(a) Connect the I85 main body ECU (multiplex network body ECU) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I85-8 (CLTB) - I85-21 (CLTE) |
Ignition switch off |
Below 1 V |
|
Ignition switch ON |
11 to 14 V |
| NG |
|
|
|
6. |
INSPECT AUTOMATIC LIGHT CONTROL SENSOR |
Click here
| OK |
|
| NG |
|
|
|