Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000028IYK |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: FRONT SUSPENSION: FRONT STABILIZER BAR: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front stabilizer bar removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Front wheel alignment adjustment
|
-
Perform "Reset Memory"
-
Perform "Calibration"
|
-
DTCs are stored
-
ABS warning light illuminates
-
Brake system warning light (yellow indicator) illuminates
-
Slip indicator light illuminates
-
Electronically controlled brake system disabled or malfunctions
|
|
-
Steering gear assembly*1
-
No. 2 steering intermediate shaft assembly*1
|
End position initial setting
|
-
|
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Front wheel alignment adjustment
|
-
Perform "Reset Memory"
-
Perform "Calibration"
|
-
VSC is disabled or malfunctions
-
DTCs are output
-
Slip indicator light illuminates
-
ABS warning light illuminates
|
w/ Electric Parking Brake System:
w/o Electric Parking Brake System:
|
-
Steering gear assembly*1
-
No. 2 steering intermediate shaft assembly*1
|
for TMC Made (except G16E-GTS)
-
End position initial setting
|
-
|
|
Tire
|
ECU Data Initialization (When performing tire replacement after RoB code X2104 is output)
|
Active Torque Split AWD System
|
|
PROCEDURE
1. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Click here
2. REMOVE FRONT STABILIZER LINK ASSEMBLY LH
(a) for G16E-GTS:
(b) Remove the nut and front stabilizer link assembly LH from the front shock absorber assembly.
NOTICE:
Do not damage the boot of the ball joint.
HINT:
If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.
|
|
3. REMOVE FRONT STABILIZER LINK ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
4. REMOVE STEERING LINK ASSEMBLY
for G16E-GTS: Click here
except G16E-GTS: Click here
5. REMOVE FRONT NO. 1 STABILIZER BRACKET LH (except G16E-GTS)
(a) Remove the 2 bolts and front stabilizer bracket LH from the front suspension crossmember sub-assembly.
|
|
6. REMOVE FRONT NO. 1 STABILIZER BRACKET RH (except G16E-GTS)
HINT:
Perform the same procedure as for the LH side.
7. REMOVE FRONT STABILIZER BRACKET (for G16E-GTS)
(a) Remove the 4 bolts and front stabilizer brackets from the front suspension crossmember sub-assembly.
|
|
8. REMOVE FRONT STABILIZER BAR
(a) Remove the front stabilizer bar with 2 front stabilizer bar bushings from the front suspension crossmember sub-assembly.
9. REMOVE FRONT STABILIZER BAR BUSHING LH
(a) Remove the front stabilizer bar bushing LH from the front stabilizer bar.
10. REMOVE FRONT STABILIZER BAR BUSHING RH
HINT:
Perform the same procedure as for the LH side.
|