Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000028IXH
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [11/2022 -           ]
Title: FRONT SUSPENSION: FRONT SHOCK ABSORBER (for G16E-GTS): REMOVAL; 2023 - 2025 MY GR Corolla [11/2022 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front shock absorber assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Front wheel alignment adjustment

  1. Perform "Reset Memory"
  2. Perform "Calibration"
  • VSC is disabled or malfunctions
  • DTCs are output
  • Slip indicator light illuminates
  • ABS warning light illuminates

2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMC Made): UTILITY

Tire

ECU Data Initialization (When performing tire replacement after RoB code X2104 is output)

Active Torque Split AWD System

2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; GF1A (TRANSFER / 4WD / AWD): ACTIVE TORQUE SPLIT AWD SYSTEM: CALIBRATION

NOTICE:

  • Remove only indicated parts.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT WHEEL

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL

2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; WIPER / WASHER: FRONT WIPER MOTOR: REMOVAL

3. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

(a) Disengage the claw and remove the No. 1 heater air duct splash shield seal from the outer cowl top panel sub-assembly.

4. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

(a) Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.

(b) Remove the 9 bolts, 4 nuts and outer cowl top panel sub-assembly.

5. REMOVE FRONT SUSPENSION SUPPORT DUST COVER

(a) Remove the front suspension support dust cover from the front shock absorber assembly.

6. LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

(a) Temporarily install the 2 nuts to the front shock absorber assembly.

(b) Loosen the front support to front shock absorber nut.

CAUTION:

  • Only loosen the front support to front shock absorber nut if the front shock absorber with coil spring needs to be disassembled.
  • Only loosen the front support to front shock absorber nut, do not remove it.
  • If the front support to front shock absorber nut is removed with the front coil spring under tension, components of the front shock absorber with coil spring may fly off.

7. SEPARATE FRONT STABILIZER LINK ASSEMBLY

(a) Remove the cap.

(b) Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.

NOTICE:

Do not damage the boot of the ball joint.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

8. SEPARATE FRONT SPEED SENSOR

(a) Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.

9. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

(a) Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.

*a

Wooden Block

*b

Jack

Front of the Vehicle

Wooden Block Placement Location

NOTICE:

Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.

(b) Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

NOTICE:

  • When removing the nuts, keep the bolts from rotating.
  • Use wire or an equivalent tool to hang the separated steering knuckle.

(c) Remove the 3 nuts, 2 spacers and front shock absorber with coil spring.

10. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

(a) Secure SST in a vise.

SST: 09727-00051

SST: 09727-30022

09727-00010

09727-00031

SST: 09727-00040

*a

SST(09727-00051)

*b

SST(09727-00040)

*c

SST(09727-30022 (09727-00010, 09727-00031))

(b) Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:

  • Make sure that the hooks are securely attached to the coil spring.
  • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
  • Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.
  • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
  • Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.
  • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

(c) Install the stopper pins to the hooks of SST.

CAUTION:

  • Make sure that the stopper pins are installed securely.
  • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

(d) Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST: 09727-30022

09727-00090

09727-00100

*a

Vehicle Nut

(e) Install SST as shown in the illustration.

CAUTION:

The pin is not attached to one side, so be sure to hang the belt.

SST: 09727-00110

(f) Using SST, compress the coil spring.

CAUTION:

  • If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.
  • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
  • Do not compress the coil spring to the point where the coils touch each other.
  • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
  • Do not use an impact wrench.
  • If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.
  • If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.
  • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

(g) Check that the coil spring has become detached, and then remove the front support to front shock absorber nut.

CAUTION:

  • Do not remove the front support to front shock absorber nut while the coil spring is under tension.
  • If the front support to front shock absorber nut is removed with the coil spring under tension, components of the front shock absorber with coil spring may fly off, resulting in injury.

11. REMOVE COLLAR

(a) Remove the collar from the front shock absorber assembly.

12. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

(a) Remove the front suspension support sub-assembly from the front shock absorber assembly.

13. REMOVE FRONT SPRING SEAT

(a) Remove the front spring seat from the front shock absorber assembly.

14. REMOVE WASHER

(a) Remove the washer from the front shock absorber assembly.

15. REMOVE STRUT MOUNTING BEARING (w/o Rear Seat Assembly)

(a) Remove the strut mounting bearing from the front shock absorber assembly.

16. REMOVE FRONT UPPER COIL SPRING INSULATOR (w/o Rear Seat Assembly)

(a) Remove the front upper coil spring insulator from the front shock absorber assembly.

17. REMOVE NO.1 FRONT SHOCK ABSORBER DUST COVER (w/o Rear Seat Assembly)

(a) Remove the No. 1 shock absorber dust cover from the front shock absorber assembly.

18. REMOVE STRUT MOUNTING BEARING WITH DUST COVER (w/ Rear Seat Assembly)

(a) Disengage the end of the front No. 1 shock absorber dust cover from the claws of the front shock absorber assembly.

*1

Front No. 1 Shock Absorber Dust Cover

*a

Claw

(b) Remove the strut mounting bearing with dust cover from the front shock absorber assembly.

19. REMOVE FRONT UPPER COIL SPRING INSULATOR (w/ Rear Seat Assembly)

(a) Remove the front upper coil spring insulator from the strut mounting bearing.

Remove in this direction

20. REMOVE STRUT MOUNTING BEARING (w/ Rear Seat Assembly)

(a) Disengage the top end of the front No. 1 shock absorber dust cover to remove the strut mounting bearing from the front No. 1 shock absorber dust cover.

21. REMOVE FRONT COIL SPRING

(a) Remove the front coil spring and SST.

NOTICE:

Do not use an impact wrench. It will damage SST.

22. REMOVE FRONT SPRING BUMPER (w/ Rear Seat Assembly)

(a) Remove the front spring bumper from the front shock absorber assembly.

23. REMOVE FRONT LOWER COIL SPRING INSULATOR

(a) Remove the front lower coil spring insulator from the front shock absorber assembly.

24. REMOVE FRONT SHOCK ABSORBER ASSEMBLY