Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000028IKU |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): P0B3B14,...,P308A13; Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] |
DTC
|
P0B3B14
|
Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open
|
DTC
|
P0B4014
|
Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open
|
DTC
|
P0B4514
|
Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open
|
DTC
|
P0B4A14
|
Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open
|
DTC
|
P0B4F14
|
Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open
|
DTC
|
P0B5414
|
Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open
|
DTC
|
P0B5914
|
Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open
|
DTC
|
P0B5E14
|
Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open
|
DTC
|
P0B6314
|
Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open
|
DTC
|
P0B6814
|
Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open
|
DTC
|
P308A13
|
Hybrid/EV Battery Voltage Sensor All Circuit Open
|
DESCRIPTION
Refer to the description for DTC P1AC000.
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Warning Indicate
|
P0B3B14
|
Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B4014
|
Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B4514
|
Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B4A14
|
Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B4F14
|
Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B5414
|
Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B5914
|
Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B5E14
|
Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B6314
|
Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P0B6814
|
Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open
|
The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
P308A13
|
Hybrid/EV Battery Voltage Sensor All Circuit Open
|
The battery block voltage detection line is open (all blocks) or all battery block voltages become lower than the specified value (possibility of open or loosely connected connector).
(1 trip detection logic)
|
-
Battery voltage sensor
-
HV battery
|
Comes on
|
Master Warning: Comes on
|
HINT:
Hybrid Battery Block 1 to 9 Voltage values smaller than 2.0 V may not be shown in the Data List because a fail-safe value is substituted.
Related Data List
DTC No.
|
Data List
|
P0B3B14
|
Hybrid/EV Battery Block 1 to 9 Voltage*1
|
P0B4014
|
P0B4514
|
P0B4A14
|
P0B4F14
|
P0B5414
|
P0B5914
|
P0B5E14
|
P0B6314
|
P0B6814
|
P308A13
|
-
Hybrid/EV Battery Voltage
-
Hybrid/EV Battery Block 1 to 9 Voltage*1
|
HINT:
-
*1: Under normal conditions, the values of Hybrid/EV Battery Block 1, 2, 8 and 9 Voltage will be approximately 16 V and Hybrid/EV Battery Block 3, 4, 5, 6 and 7 Voltage will be approximately 32 V.
-
If there is a short or open in a battery block voltage detection line, the value of Hybrid Battery Block Voltage for the corresponding battery block will be lower than 8 V.
MONITOR DESCRIPTION
If the battery voltage sensor detects a voltage drop in a battery block, the hybrid vehicle control ECU will illuminate the MIL and store a DTC.
MONITOR STRATEGY
Related DTCs
|
P0B3D (INF P0B3B14), P0B42 (INF P0B4014), P0B47 (INF P0B4514), P0B4C (INF P0B4A14), P0B51 (INF P0B4F14), P0B56 (INF P0B5414), P0B5B (INF P0B5914), P0B60 (INF P0B5E14), P0B65 (INF P0B6314), P0B6A (INF P0B6814), P308A (INF P308A13): Battery voltage sensor circuit malfunction (open)
|
Required sensors/components
|
Battery voltage sensor
|
Frequency of operation
|
Continuous
|
Duration
|
TMC's intellectual property
|
MIL operation
|
Immediately
|
Sequence of operation
|
None
|
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored
|
TMC's intellectual property
|
Other conditions belong to TMC's intellectual property
|
-
|
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property
|
-
|
COMPONENT OPERATING RANGE
Battery voltage sensor
|
DTC P0B3D (INF P0B3B14) is not detected
DTC P0B42 (INF P0B4014) is not detected
DTC P0B47 (INF P0B4514) is not detected
DTC P0B4C (INF P0B4A14) is not detected
DTC P0B51 (INF P0B4F14) is not detected
DTC P0B56 (INF P0B5414) is not detected
DTC P0B5B (INF P0B5914) is not detected
DTC P0B60 (INF P0B5E14) is not detected
DTC P0B65 (INF P0B6314) is not detected
DTC P0B6A (INF P0B6814) is not detected
DTC P308A (INF P308A13) is not detected
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the power switch on (IG) and turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the power switch off and wait for 2 minutes or more.
-
Turn the power switch on (IG) and turn the Techstream on.
-
With power switch on (IG) and wait for 20 seconds or more.[*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
-
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to the precautions before inspecting high voltage circuit.
Click here
CAUTION / NOTICE / HINT
CAUTION:
-
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
-
Inspecting the high-voltage system
-
Disconnecting the low voltage connector of the inverter with converter assembly
-
Disconnecting the low voltage connector of the HV battery
-
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
-
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
-
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here
HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
|
Without waiting for 10 minutes
|
-
Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.
If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.
-
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
*a
|
Dealer
|
*b
|
Battery Collection Agent
|
-
Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
-
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
PROCEDURE
1.
|
CHECK DTC OUTPUT (HYBRID CONTROL)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check and record any HV system DTCs and freeze frame data.
(e) Read output DTCs.
Powertrain > Hybrid Control > Trouble Codes
Result
|
Proceed to
|
P0A9563, P0AFC00, P0AFC96 or P308A12 is not output.
|
A
|
P0A9563, P0AFC00, P0AFC96 or P308A12 is output.
|
B
|
(f) Turn the power switch off.
A
|
|
|
2.
|
CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR CONNECTOR)
|
Click here
NG |
|
CONNECT SECURELY
|
OK
|
|
|
3.
|
CHECK DTC OUTPUT (HYBRID CONTROL)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes
HINT:
Check the DTCs that were output when the vehicle was brought to the workshop.
Result
|
Proceed to
|
DTCs other than P308A13 are also output.
|
A
|
P308A13 is output
|
B
|
(e) Turn the ignition switch off.
A
|
|
|
4.
|
CHECK BATTERY VOLTAGE SENSOR (BLOCK VOLTAGES)
|
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect the high voltage cable connector of the HV battery from the HV battery junction block assembly.
NOTICE:
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
(c) Disconnect the z13 battery voltage sensor connector.
(d) Measure the voltage according to the value(s) in the table below.
HINT:
For each output DTC, apply the judgment method in the table below and calculate the voltage value.
*a
|
Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)
|
Standard Voltage:
DTC No.
|
Judgment Method
|
Specified Condition
|
P0B6814
|
[A] = [C]
|
201.6 to 235.2 V
|
P0B6314
|
[D]
|
14.4 to 16.8 V
|
P0B5E14
|
[E] - [D]
|
14.4 to 16.8 V
|
P0B5914
|
[F] - [E]
|
28.8 to 33.6 V
|
P0B5414
|
[G] - [F]
|
28.8 to 33.6 V
|
P0B4F14
|
[H] - [I]
|
28.8 to 33.6 V
|
P0B4A14
|
[I] - [J]
|
28.8 to 33.6 V
|
P0B4514
|
[J] - [K]
|
14.4 to 16.8 V
|
P0B4014
|
[K]
|
14.4 to 16.8 V
|
P0B3B14
|
[A] = [B]
|
201.6 to 235.2 V
|
Tester Connection
|
Condition
|
Specified Condition
|
Service plug grip connecting terminals 1 (+) - z14-1 (-) (-)
|
Ignition switch off
|
[A]
|
Service plug grip connecting terminals 1 (+) - z13-18 (GB0) (-)
|
Ignition switch off
|
[B]
|
z13-11 (VB14) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[C]
|
Service plug grip connecting terminals 1 (+) - z13-3 (VB13) (-)
|
Ignition switch off
|
[D]
|
Service plug grip connecting terminals 1 (+) - z13-12 (VB12) (-)
|
Ignition switch off
|
[E]
|
Service plug grip connecting terminals 1 (+) - z13-13 (VB10) (-)
|
Ignition switch off
|
[F]
|
Service plug grip connecting terminals 1 (+) - z13-14 (VB8) (-)
|
Ignition switch off
|
[G]
|
z13-15 (VB6) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[H]
|
z13-16 (VB4) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[I]
|
z13-17 (VB2) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[J]
|
z13-9 (VB1) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[K]
|
CAUTION:
Make sure not to cross the electrodes of an electrical tester measurement terminals.
NOTICE:
Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.
(e) Disconnect the z13 battery voltage sensor connector.
(f) Reconnect the HV battery high voltage cable connectors.
5.
|
CHECK BATTERY VOLTAGE SENSOR (BLOCK VOLTAGES)
|
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect the high voltage cable connector of the HV battery from the HV battery junction block assembly.
NOTICE:
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
(c) Disconnect the z13 battery voltage sensor connector.
(d) Measure the voltage according to the value(s) in the table below.
HINT:
Apply the judgment method in the table below and calculate the voltage value.
*a
|
Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)
|
Standard Voltage:
DTC No.
|
Judgment Method
|
Specified Condition
|
P308A13
|
[C] - [D]
|
28.8 to 33.6 V
|
[D] - [E]
|
14.4 to 16.8 V
|
[E]
|
14.4 to 16.8 V
|
[A] = [B]
|
201.6 to 235.2 V
|
Tester Connection
|
Condition
|
Specified Condition
|
Service plug grip connecting terminals 1 (+) - z14-1 (-) (-)
|
Ignition switch off
|
[A]
|
Service plug grip connecting terminals 1 (+) - z13-18 (GB0) (-)
|
Ignition switch off
|
[B]
|
z13-16 (VB4) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[C]
|
z13-17 (VB2) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[D]
|
z13-9 (VB1) (+) - z14-1 (-) (-)
|
Ignition switch off
|
[E]
|
CAUTION:
Make sure not to cross the electrodes of an electrical tester measurement terminals.
NOTICE:
Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.
(e) Disconnect the z13 battery voltage sensor connector.
(f) Reconnect the HV battery high voltage cable connectors.
|