WINDOW / GLASS: WINDSHIELD GLASS: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000028IJ2
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [11/2022 - ]
Title: WINDOW / GLASS: WINDSHIELD GLASS: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield glass removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Windshield glass*

Adjust forward recognition camera

Front Camera System
Automatic High Beam System

One Time Recognition:

Driving Adjustment:

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedures are not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Windshield glass*

Adjust forward recognition camera

for TMC Made

Front Camera System
Automatic High Beam System

One Time Recognition:

Driving Adjustment:

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

for HV Model:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

for Gasoline Model:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
1: for GR Model 2: except GR Model
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.1 Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.2

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

CAUTION / NOTICE / HINT

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane control system, road sign assist system, pre-collision system, front camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.

PROCEDURE

1. REMOVE FRONT WIPER ARM HEAD CAP

Click here

2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Click here

3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Click here

4. REMOVE COWL WATER EXTRACT SHIELD LH

Click here

5. REMOVE COWL WATER EXTRACT SHIELD RH

HINT:

Use the same procedure as for the LH side.

6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here

7. REMOVE INNER REAR VIEW MIRROR ASSEMBLY

w/o EC Mirror:

Click here

w/ EC Mirror:

Click here

8. REMOVE FORWARD RECOGNITION CAMERA

Click here

9. REMOVE ROOF HEADLINING ASSEMBLY

for Hatchback:

Click here

for Sedan:

Click here

10. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

(a) w/ Windshield Deicer System:

(1) Disconnect the connector.

(b) Apply protective tape to the area around the installation position of the windshield glass sub-assembly on the vehicle body to prevent it from being scratched.

Protective Tape

*1	Windshield Glass
*2	Windshield Outside Moulding
*a	Cut

(d) Place matchmarks on the windshield glass sub-assembly and vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.

Matchmark

(e) When using a windshield knife:

(1) Apply soapy water to the area around the adhesive.

(2) Insert a windshield knife into the adhesive between the windshield glass sub-assembly and vehicle body.

*a	Windshield Knife
*b	Aligned with Windshield Glass Sub-assembly
	Pull

(3) While keeping the windshield knife perpendicular to the outer surface of the windshield glass sub-assembly, cut the adhesive by pulling the windshield knife around the windshield glass sub-assembly.

NOTICE:

Do not pry the windshield glass sub-assembly with the windshield knife.
Do not use a windshield knife to cut the adhesive on the lower side of the windshield glass sub-assembly.
When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

HINT:

Insert the windshield knife in an area where the gap between windshield glass sub-assembly and vehicle body is large.

(f) When using piano wire:

(1) Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.

(2) Tie both wire ends to wooden blocks or similar objects that can serve as handles.

(3) Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.

NOTICE:

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.
Be careful not to damage the front window inner center moulding.

*1	Windshield Glass Stopper
*2	Front Window Inner Center Moulding
*a	Piano Wire

(g) Disengage the windshield glass stoppers.

*A	for 1-piece Type	*B	for 2-piece Type
*1	No. 1 Windshield Glass Stopper	*2	No. 2 Windshield Glass Stopper

NOTICE:

The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass sub-assembly as shown in the illustration. Be careful not to damage the windshield glass sub-assembly when cutting the adhesive.
To prevent the windshield glass sub-assembly from falling when performing this operation, be sure to hold the windshield glass sub-assembly using suction cups.

(h) Using suction cups, remove the windshield glass sub-assembly.

NOTICE:

Be careful not to drop the windshield glass sub-assembly.
Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.

11. REMOVE WINDOW GLASS ADHESIVE DAM

(a) When reusing the windshield glass:

(1) Using a scraper, remove the window glass adhesive dam.

NOTICE:

Be careful not to damage the windshield glass.
Be sure to replace the window glass adhesive dam with a new one.

Back Side

12. REMOVE WINDSHIELD OUTSIDE MOULDING

(a) When reusing the windshield glass:

(1) Using a scraper, remove the windshield outside moulding.

NOTICE:

Be careful not to damage the windshield glass.
Be sure to replace the windshield outside moulding with a new one.

Back Side

13. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

(a) When reusing the windshield glass:

(1) Using a scraper, remove the 2 No. 1 windshield glass stoppers.

NOTICE:

Be careful not to damage the windshield glass.
Be sure to replace the No. 1 windshield glass stoppers with new ones.

Back Side

14. REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

(a) When reusing the windshield glass:

(1) Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:

Be careful not to damage the windshield glass.
Be sure to replace the No. 2 windshield glass stoppers with new ones.

Back Side

15. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

(a) Remove the 2 No. 1 windshield glass stoppers from the vehicle body.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.

16. REMOVE FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of a front window inner center moulding is necessary.

(a) Place matchmarks on the windshield glass at the locations indicated in the illustration.

*A	Back Side
*a	Matchmark

(b) Using a scraper, remove the front window inner center moulding.

NOTICE:

Be careful not to damage the windshield glass.
Be sure to replace the front window inner center moulding with a new one.

17. CLEAN WINDSHIELD GLASS

(a) When reusing the windshield glass:

(1) Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.

(2) Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:

Do not touch the windshield glass surface after cleaning it.
Even if using a new windshield glass, clean it with a non-residue solvent.

18. CLEAN VEHICLE BODY

(a) Clean and shape the contact surface of the vehicle body.

(1) Using a knife, cut off any excess adhesive on the contact surface of the vehicle body as shown in the illustration.

*a	Vehicle Body
	Adhesive

Standard Dimension:

Area	Dimension
a	1.0 mm (0.0394 in.) or more

NOTICE:

Be careful not to damage the vehicle body.

HINT:

Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.

(2) Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the vehicle body.