| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000028HYZ |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY (for Sedan): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear 3 point type seat outer belt assembly removal/installation are shown below.
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
PROCEDURE
1. PRECAUTION (w/ Pretensioner)
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
NOTICE:
After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Pretensioner)
for M20A-FKS: Click here
for 2ZR-FXE: Click here
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
3. REMOVE REAR SEAT ASSEMBLY
Click here
4. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)
Click here
5. REMOVE REAR DOOR SCUFF PLATE RH (for Gasoline Model)
HINT:
Use the same procedure as for the LH side.
6. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)
Click here
7. REMOVE REAR DOOR SCUFF PLATE RH (for HV Model)
HINT:
Use the same procedure as for the LH side.
8. REMOVE REAR UNDER SIDE COVER LH (for HV Model)
Click here
9. REMOVE REAR UNDER SIDE COVER RH (for HV Model)
HINT:
Use the same procedure as for the LH side.
10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
(a) Disconnect the rear door opening trim weatherstrip LH.
11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
12. REMOVE REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag)
Click here
13. REMOVE REAR SEAT SIDE GARNISH LH (w/ Rear Seat Side Airbag)
Click here
14. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE ROOF SIDE INNER GARNISH LH
Click here
16. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
17. REMOVE CENTER STOP LIGHT SET
Click here
18. REMOVE PACKAGE TRAY TRIM BRACKET LH
|
(a) Disengage the 3 clips and 4 claws to remove the package tray trim bracket LH. |
|
19. REMOVE PACKAGE TRAY TRIM BRACKET RH
HINT:
Use the same procedure as for the LH side.
20. REMOVE REAR SEAT SHOULDER BELT HOLE COVER
|
(a) Disengage the 2 claws and 2 guides to remove the rear seat shoulder belt hole cover. |
|
21. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
|
(a) Remove the 3 clips. |
|
|
(b) Disengage the 5 guides to remove the package tray trim panel assembly. |
|
22. REMOVE REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH WITH BRACKET
|
(a) Remove the bolt to disconnect the floor anchor of the rear 3 point type seat outer belt assembly LH. |
|
(b) w/o Pretensioner:
|
(1) Remove the 2 bolts. |
|
(2) Disengage the guide to remove the rear 3 point type seat outer belt assembly LH with bracket.
(c) w/ Pretensioner:
|
(1) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector. HINT: Tape the screwdriver tip before use. |
|
|
(2) Remove the 2 bolts. |
|
(3) Disengage the guide to remove the rear 3 point type seat outer belt assembly LH with bracket.
23. REMOVE REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH WITH BRACKET
HINT:
Use the same procedure as for the LH side.
24. REMOVE REAR SEAT BELT RETRACTOR COVER LH
|
(a) Remove the rear seat belt retractor cover LH. |
|
25. REMOVE REAR SEAT BELT RETRACTOR COVER RH
HINT:
Use the same procedure as for the LH side.
26. REMOVE REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH
(a) Hold the rear 3 point type seat outer belt assembly LH with bracket in a vise between aluminum plates.
NOTICE:
Do not overtighten the vise.
|
(b) Remove the nut. |
|
(c) Disengage the 2 guides to remove the rear 3 point type seat outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.
27. REMOVE REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
|
|