DOOR LOCK: FRONT DOOR LOCK: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM1000000028HXF
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [11/2022 - ]
Title: DOOR LOCK: FRONT DOOR LOCK: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
Front door glass sub-assembly1 Front door glass run1 Front door inner glass weatherstrip*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Key-off operation function Catch protection function Window open warning function

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
Front door glass sub-assembly1 Front door glass run1 Front door inner glass weatherstrip*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

HINT:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
1: for GR Model 2: except GR Model
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.1 Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.2

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)

Click here

3. REMOVE SPARE WHEEL CUSHION (for G16E-GTS)

for Type A:

Click here

4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FKS:

Click here

for 2ZR-FXE:

Click here

for G16E-GTS:

Click here

5. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

Click here

6. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY

Click here

7. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

10. REMOVE DOOR UPPER FRAME GARNISH

Click here

11. REMOVE FRONT DOOR VENT SEAL

Click here

12. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here

13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here

14. REMOVE FRONT DOOR GLASS RUN

Click here

15. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Click here

16. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Lock Cylinder)

Click here

17. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)

Click here

18. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

(a) Disconnect the connector.

*1	Front Door Lock Open Rod
	Remove in this Direction

(b) Using a T30 "TORX" socket wrench, remove the 3 screws.

(c) Slide the front door lock with motor assembly downward as shown in the illustration to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.

(d) When reusing the front door lock with motor assembly:

(1) Remove the door lock wiring harness seal from the front door lock with motor assembly.

19. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY

(a) Using a screwdriver, disengage the 2 claws as shown in the illustration.

(b) for TMMMS Made:

(1) Disengage the 2 claws to remove the front door lock cover sub-assembly as shown in the illustration.

Remove in this Direction

(1) Disengage the claw to remove the front door lock cover sub-assembly as shown in the illustration.

Remove in this Direction

20. REMOVE FRONT DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE

(a) Remove the front door lock open lever remote control cable as shown in the illustration.

Remove in this Direction

21. REMOVE FRONT DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE

(a) Remove the front door inside lock/unlock knob locking cable as shown in the illustration.

Remove in this Direction