DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000028HXB
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [11/2022 - ]
Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
Rear door glass sub-assembly1 Rear door glass run1 Rear door inner glass weatherstrip*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Key-off operation function Catch protection function Window open warning function

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
Rear door glass sub-assembly1 Rear door glass run1 Rear door inner glass weatherstrip*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

HINT:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
1: for GR Model 2: except GR Model
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.1 Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.2

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)

Click here

3. REMOVE SPARE WHEEL CUSHION (for G16E-GTS)

for Type A:

Click here

4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FKS:

Click here

for 2ZR-FXE:

Click here

for G16E-GTS:

Click here

5. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here

6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

8. REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Click here

9. REMOVE REAR DOOR FRAME GARNISH

Click here

10. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here

11. REMOVE REAR DOOR PANEL PROTECTOR

Click here

12. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

13. REMOVE REAR DOOR WINDOW REGULATOR LIFT ARM BRACKET (w/o Rear Seat Assembly)

Click here

14. REMOVE REAR DOOR GLASS RUN

Click here

15. DISCONNECT REAR DOOR WEATHERSTRIP

(a) Disconnect the rear door weatherstrip until the screw of the rear door window division bar sub-assembly is visible.

16. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Click here

17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

18. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

(a) Disconnect the connector.

*a	Release Plate
	Remove in this Direction

(b) Using a T30 "TORX" socket wrench, remove the 3 screws.

(c) Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.

(d) When reusing the rear door lock with motor assembly:

(1) Remove the door lock wiring harness seal from the rear door lock with motor assembly.

19. REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY (for TMC Made)

(a) Using a screwdriver, disengage the 2 claws as shown in the illustration.

(b) Disengage the claw to remove the rear door lock cover sub-assembly as shown in the illustration.

Remove in this Direction

20. REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE

(a) for TMMMS Made:

(1) Using a screwdriver, disengage the claw and open the cover as shown in the illustration.

(2) Remove the rear door lock open lever remote control cable as shown in the illustration.

Remove in this Direction

(b) for TMC Made:

(1) Remove the rear door lock open lever remote control cable as shown in the illustration.

Remove in this Direction

21. REMOVE REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE

(a) for TMMMS Made:

(1) Using a screwdriver, disengage the 3 claws and open the cover as shown in the illustration.

(2) Remove the rear door inside lock/unlock knob locking cable as shown in the illustration.

Remove in this Direction

(b) for TMC Made:

(1) Remove the rear door inside lock/unlock knob locking cable as shown in the illustration.

Remove in this Direction