| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000028HX9 |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: DOOR LOCK: REAR DOOR LOCK: INSTALLATION; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] | ||
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. INSTALL REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE
(a) for TMMMS Made:
(1) Install the rear door inside lock/unlock knob locking cable as shown in the illustration.
|
Install in this Direction |
|
(2) Engage the 3 claws to close the cover as shown in the illustration. |
|
(b) for TMC Made:
(1) Install the rear door inside lock/unlock knob locking cable as shown in the illustration.
|
|
Install in this Direction |
3. INSTALL REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE
(a) for TMMMS Made:
(1) Install the rear door lock open lever remote control cable as shown in the illustration.
|
|
Install in this Direction |
|
(2) Engage the claw to close the cover as shown in the illustration. |
|
(b) for TMC Made:
(1) Install the rear door lock open lever remote control cable as shown in the illustration.
|
|
Install in this Direction |
4. INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY (for TMC Made)
|
|
Install in this Direction |
(a) Engage the claw as shown in the illustration.
|
(b) Engage the 2 claws to install the rear door lock cover sub-assembly as shown in the illustration. |
|
5. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY
NOTICE:
- When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.
- Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
- Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.
(a) When reusing the rear door lock with motor assembly:
(1) Install a new door lock wiring harness seal to the rear door lock with motor assembly.
(b) Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly as shown in the illustration, and set it to the rear door panel.
|
*a |
Release Plate |
|
|
Install in this Direction |
HINT:
Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly.
(c) Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
(d) Connect the connector.
6. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]; DOOR / HATCH: REAR DOOR: REASSEMBLY+](/t3Portal/stylegraphics/info.gif)
7. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Click here
8. CONNECT REAR DOOR WEATHERSTRIP
(a) Connect the rear door weatherstrip.
9. INSTALL REAR DOOR GLASS RUN
Click here
10. INSTALL REAR DOOR WINDOW REGULATOR LIFT ARM BRACKET (w/o Rear Seat Assembly)
Click here
11. INSTALL REAR DOOR SERVICE HOLE COVER
Click here
12. INSTALL REAR DOOR PANEL PROTECTOR
Click here
13. INSTALL REAR DOOR NO. 1 VENT SEAL
Click here
14. INSTALL REAR DOOR FRAME GARNISH
Click here
15. INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)
Click here
16. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
18. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
Click here
19. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS:
Click here
for 2ZR-FXE:
Click here
for G16E-GTS:
Click here
20. INSTALL SPARE WHEEL CUSHION (for G16E-GTS)
for Type A:
Click here
21. INSTALL DECK BOARD ASSEMBLY (for G16E-GTS)
Click here
22. INITIALIZE POWER WINDOW CONTROL SYSTEM
Click here
23. INSPECT POWER WINDOW OPERATION
Click here
|
|