|
Last Modified: 01-27-2025 |
6.11:8.1.0 |
Doc ID: RM1000000028HW3 |
|
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [11/2022 -
] |
|
Title: M20A-FKS (FUEL): FUEL TANK (w/o Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
|
Gas leak from exhaust system is repaired
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
|
Front Camera System
|
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
|
|
Learning completes when vehicle is operated normally
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
PROCEDURE
1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Click here
2. DRAIN FUEL
3. REMOVE TAIL EXHAUST PIPE ASSEMBLY
Click here
4. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
|
(a) Remove the nut, 4 clips and No. 1 fuel tank protector sub-assembly from the fuel tank assembly.
|
|
5. DISCONNECT CHARCOAL CANISTER OUTLET HOSE
|
(a) Disconnect the charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.
|
|
6. DISCONNECT FUEL TANK TO FILLER PIPE HOSE
|
(a) Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.
|
|
7. DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
|
(a) Disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.
Click here
|
|
8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
|
(a) Disconnect the fuel tank main tube sub-assembly from the fuel pipe.
Click here
|
|
9. REMOVE FUEL TANK ASSEMBLY
CAUTION:
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
|
(a) Disconnect the fuel tank breather tube from the fuel tank filler pipe sub-assembly.
Click here
|
|
|
(b) Support the fuel tank assembly using an engine lifter.
HINT:
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
|
|
|
(c) Remove the 4 bolts, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH.
|
|
(d) Lower the engine lifter to remove the fuel tank assembly.
NOTICE:
-
Be careful not to drop the fuel tank assembly.
-
When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
10. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
|
(a) Disengage the 4 clamps to remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.
|
|
11. REMOVE CHARCOAL CANISTER OUTLET HOSE
|
(a) Disengage the 2 clamps to remove the charcoal canister outlet hose from the fuel tank assembly.
|
|
12. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
|
(a) Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.
|
|
13. REMOVE NO. 2 FUEL TANK CUSHION
|
(a) Remove the 2 No. 2 fuel tank cushions from the fuel tank assembly.
|
|
|