Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000028HW3 |
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [11/2022 -
] |
Title: M20A-FKS (FUEL): FUEL TANK (w/o Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Gas leak from exhaust system is repaired
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Front Camera System
|
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
|
|
Learning completes when vehicle is operated normally
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
PROCEDURE
1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Click here
2. DRAIN FUEL
3. REMOVE TAIL EXHAUST PIPE ASSEMBLY
Click here
4. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
(a) Remove the nut, 4 clips and No. 1 fuel tank protector sub-assembly from the fuel tank assembly.
|
|
5. DISCONNECT CHARCOAL CANISTER OUTLET HOSE
(a) Disconnect the charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.
|
|
6. DISCONNECT FUEL TANK TO FILLER PIPE HOSE
(a) Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.
|
|
7. DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
(a) Disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.
Click here
|
|
8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
(a) Disconnect the fuel tank main tube sub-assembly from the fuel pipe.
Click here
|
|
9. REMOVE FUEL TANK ASSEMBLY
CAUTION:
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
(a) Disconnect the fuel tank breather tube from the fuel tank filler pipe sub-assembly.
Click here
|
|
(b) Support the fuel tank assembly using an engine lifter.
HINT:
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
|
|
(c) Remove the 4 bolts, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH.
|
|
(d) Lower the engine lifter to remove the fuel tank assembly.
NOTICE:
-
Be careful not to drop the fuel tank assembly.
-
When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
10. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
(a) Disengage the 4 clamps to remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.
|
|
11. REMOVE CHARCOAL CANISTER OUTLET HOSE
(a) Disengage the 2 clamps to remove the charcoal canister outlet hose from the fuel tank assembly.
|
|
12. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
(a) Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.
|
|
13. REMOVE NO. 2 FUEL TANK CUSHION
(a) Remove the 2 No. 2 fuel tank cushions from the fuel tank assembly.
|
|
|