M20A-FKS (FUEL): FUEL PUMP (for High Pressure): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback [11/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000028HVX
Model Year Start: 2023	Model: Corolla Hatchback	Prod Date Range: [11/2022 - ]
Title: M20A-FKS (FUEL): FUEL PUMP (for High Pressure): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Replacement of fuel pump assembly Replacement of throttle body with motor assembly Cleaning the deposits from the throttle body with motor assembly Replacement of EGR valve assembly Gas leak from exhaust system is repaired	Inspection after repair	Poor idle, etc. Engine start function, etc.

CAUTION:

Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here

2. DISCHARGE FUEL SYSTEM PRESSURE

Click here

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here

4. REMOVE EGR VALVE ASSEMBLY

Click here

5. REMOVE INTAKE MANIFOLD

Click here

6. DISCONNECT FUEL TUBE SUB-ASSEMBLY

(a) Disconnect the fuel tube sub-assembly from the fuel pump assembly.

Click here

7. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

(a) Disconnect the ignition coil assembly connector.

(b) Using an 8 mm socket wrench, remove the bolt.

(d) Loosen the 2 bolts of the fuel pump assembly.

(e) Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.

8. REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.

(a) Disconnect the fuel pump assembly connector.

(b) Remove the 2 bolts, fuel pump assembly and fuel pump flange from the cylinder head cover sub-assembly.

(d) Remove the fuel pump lifter assembly from the fuel pump lifter guide.

(e) Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.