Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000028HVM
Model Year Start: 2023 Model: Corolla Hatchback Prod Date Range: [11/2022 -           ]
Title: M20A-FKS (FUEL): FUEL INJECTOR (for Direct Injection): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during direct fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

  • Replacement of direct fuel injector assembly
  • Replacement of fuel pump assembly
  • Replacement of throttle body with motor assembly
  • Cleaning the deposits from the throttle body with motor assembly
  • Replacement of EGR valve assembly
  • Gas leak from exhaust system is repaired

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

2023 - 2025 MY Corolla Corolla Hatchback [11/2022 -        ]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

CAUTION:

  • Never perform work on fuel system components near any possible ignition sources.
  • Vaporized fuel could ignite, resulting in a serious accident.
  • Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
  • Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
  • To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Front Camera System

Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; ADVANCED DRIVER ASSISTANCE SYSTEM: FRONT CAMERA SYSTEM: INITIALIZATION

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: for Hatchback

Power Door Lock Control System

  • Back door opener*1

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

PROCEDURE

1. REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback [11/2022 -        ]; M20A-FKS (FUEL): FUEL PUMP (for High Pressure): REMOVAL

2. REMOVE FUEL DELIVERY PIPE

NOTICE:

When replacing the fuel delivery pipe, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.

(a) Disengage the clamp.

(b) Disconnect the 4 direct fuel injector assembly connectors.

NOTICE:

Make sure to disconnect the connectors carefully.

(c) Remove the 4 bolts and fuel delivery pipe with the 4 direct fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

  • If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
  • Make sure not to touch or strike the tips of the direct fuel injector assemblies.
  • Pull and remove the fuel delivery pipe in a straight line without tilting it.

3. REMOVE DIRECT FUEL INJECTOR ASSEMBLY

(a) Secure the fuel delivery pipe in a vise between aluminum plates and pull out the 4 direct fuel injector assemblies.

NOTICE:

  • Pull and remove each direct fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe O-ring.
  • After removing the direct fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe side.
  • Attach a tag or label with the corresponding cylinder number to each direct fuel injector assembly so that they can be installed to their original locations.
  • Cover the tip of each direct fuel injector assembly to prevent it from being damaged.

(b) Remove the nozzle holder clamp from each direct fuel injector assembly.

(c) Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each direct fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.

(d) Remove the O-ring and No. 1 fuel injector back-up ring from each direct fuel injector assembly.

(e) Remove the C-ring and injector vibration insulator from each direct fuel injector assembly.

4. REMOVE FUEL INJECTOR SEAL

(a) Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:

  • Excessively pinching the fuel injector seal may damage the groove of the direct fuel injector assembly.
  • If a direct fuel injector assembly is dropped or the tip of the direct fuel injector assembly is struck, replace it with a new one.

(b) Remove the fuel injector seal from each direct fuel injector assembly.