EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000028HGU
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [11/2022 - ]
Title: EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door belt moulding from the door frame removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
Door glass1 Door glass run1 Door glass weatherstrip inner*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
Door glass1 Door glass run1 Door glass weatherstrip inner*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Key-off operation function Catch protection function Window open warning function

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

for HV Model:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

for Gasoline Model:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
1: for GR Model 2: except GR Model
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.1 Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.2

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Use the same procedure for the RH side and LH side.

The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)

Click here

3. REMOVE SPARE WHEEL CUSHION (for G16E-GTS)

Click here

4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for G16E-GTS: Click here

for M20A-FKS: Click here

for 2ZR-FXE: Click here

5. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

Click here

6. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY

Click here

7. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

10. REMOVE DOOR UPPER FRAME GARNISH

Click here

11. REMOVE FRONT DOOR VENT SEAL

Click here

12. REMOVE NO. 3 FRONT DOOR SERVICE HOLE COVER

Click here

13. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here

14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here

15. REMOVE FRONT DOOR GLASS RUN

Click here

16. DISCONNECT FRONT DOOR WEATHERSTRIP

(a) Disconnect the front door weatherstrip until the screw of the front door front lower frame sub-assembly is visible.

17. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

Click here

18. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP WITH FRONT DOOR FIX WINDOW GLASS

Click here

19. REMOVE FRONT DOOR BELT MOULDING

(a) Apply protective tape around the front door belt moulding as shown in the illustration.

Protective Tape

Remove in this Direction

(b) Disengage the 8 claws as shown in the illustration to remove the front door belt moulding.