EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM1000000028HGT
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [11/2022 - ]
Title: EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding from the door frame removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
Door glass1 Door glass run1 Door glass weatherstrip inner*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
Door glass1 Door glass run1 Door glass weatherstrip inner*1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Key-off operation function Catch protection function Window open warning function

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

for HV Model:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

for Gasoline Model:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
1: for GR Model 2: except GR Model
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.1 Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.2

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Use the same procedure for the RH side and LH side.

The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)

Click here

3. REMOVE SPARE WHEEL CUSHION (for G16E-GTS)

Click here

4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for G16E-GTS: Click here

for M20A-FKS: Click here

for 2ZR-FXE: Click here

5. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here

6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

8. REMOVE REAR SPEAKER ASSEMBLY (w/ SPEAKER)

Click here

9. REMOVE REAR DOOR FRAME GARNISH

Click here

10. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here

11. REMOVE REAR DOOR PANEL PROTECTOR

Click here

12. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

13. REMOVE REAR DOOR WINDOW REGULATOR LIFT ARM BRACKET (w/o Rear Seat Assembly)

Click here

14. REMOVE REAR DOOR GLASS RUN

Click here

15. DISCONNECT REAR DOOR WEATHERSTRIP

Click here

16. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Click here

17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

18. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP WITH REAR DOOR QUARTER WINDOW GLASS

Click here

19. REMOVE REAR DOOR BELT MOULDING (for Hatchback)

(a) Apply protective tape around the rear door belt moulding as shown in the illustration.

Protective Tape

(b) Disengage the 7 claws as shown in the illustration to remove the rear door belt moulding.

Remove in this Direction

20. REMOVE REAR DOOR BELT MOULDING (for Sedan)

(a) Apply protective tape around the rear door belt moulding as shown in the illustration.

Protective Tape

(b) Disengage the 8 claws as shown in the illustration to remove the rear door belt moulding.

Remove in this Direction