Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000028HAJ |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): B150819; Turn Signal/Hazard Flasher Circuit Current Above Threshold; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] |
DTC
|
B150819
|
Turn Signal/Hazard Flasher Circuit Current Above Threshold
|
DESCRIPTION
This DTC is stored when the combination meter assembly detects a short in a turn signal light circuit.
HINT:
If there is a short in a turn signal light circuit, the turn signal lights on the side with the short circuit will blink faster than usual.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
DTC Output from
|
Priority
|
B150819
|
Turn Signal/Hazard Flasher Circuit Current Above Threshold
|
Diagnosis Condition:
-
Auxiliary battery voltage is 10 V or more
Malfunction Status:
-
Short in turn signal light circuit
|
-
Headlight unit assembly
-
Rear Combination Light Assembly
-
Rear turn signal light LED
-
Outer rear view mirror assembly
-
Side turn signal light assembly
-
Harness or connector
-
Combination meter assembly
|
Combination Meter
|
A
|
WIRING DIAGRAM
LH SIDE
RH SIDE
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing any of the following ECUs, always replace it with a new one. If any of the following ECUs is replaced with one which was installed to another vehicle, the information stored in it will not match the information from the vehicle and a DTC may be stored.
-
When replacing the combination meter assembly, update the ECU security key.
Click here
-
Inspect the turn signal light bulbs before performing the following procedure.
PROCEDURE
(a) Inspect the illumination of each turn signal light.
Result
|
Proceed to
|
All LH turn signal lights do not blink
|
A
|
All RH turn signal lights do not blink
|
B
|
A
|
|
|
2.
|
CHECK LH SIDE LIGHTS (REAR COMBINATION LIGHT ASSEMBLY LH)
|
(a) Disconnect the O104*1, O43*2 rear combination light assembly LH connector.
(b) Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the rear turn signal light blink.
HINT:
If the LH side turn signal lights blink, the rear light assembly LH is malfunctioning.
-
*1: for Sedan
-
*2: for Hatchback
Result
|
Proceed to
|
LH side turn signal lights blink
|
A
|
LH side turn signal lights do not blink
|
B
|
A |
|
REPLACE REAR COMBINATION LIGHT ASSEMBLY LH
for Hatchback: Click here
for Sedan: Click here
|
B
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY)
|
(a) Disconnect the O104*1, O43*2 combination light assembly LH connector.
(b) Disconnect the I5 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (for Sedan):
Tester Connection
|
Condition
|
Specified Condition
|
O104-3 (B) or I5-22 (TRNL) - Body ground
|
Always
|
10 kΩ or higher
|
Standard Resistance (for Hatchback):
Tester Connection
|
Condition
|
Specified Condition
|
O43-4 (B) or I5-22 (TRNL) - Body ground
|
Always
|
10 kΩ or higher
|
-
*1: for Sedan
-
*2: for Hatchback
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK LH SIDE LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)
|
(a) Connect the O104*1, O43*2 rear combination light assembly LH connector.
(b) Connect the I5 combination meter assembly connector.
(c) Disconnect the L9 outer rear view mirror assembly LH connector.
(d) Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the side turn signal light blink.
HINT:
If the LH side turn signal lights blink, the outer rear view mirror assembly LH is malfunctioning.
-
*1: for Sedan
-
*2: for Hatchback
Result
|
Proceed to
|
LH side turn signal lights blink
|
A
|
LH side turn signal lights do not blink
|
B
|
A
|
|
|
5.
|
INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
|
Click here
6.
|
CHECK LH SIDE LIGHTS (HEADLIGHT ASSEMBLY LH)
|
(a) Connect the L9 outer rear view mirror assembly LH connector.
(b) Disconnect the A131*1, A134*2 headlight assembly LH connector.
(c) Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the headlight turn signal light blink.
HINT:
If the LH side turn signal lights blink, the headlight assembly LH is malfunctioning.
-
*1: for LED Type Front Turn Signal Light
-
*2: for Bulb Type Front Turn Signal Light
Result
|
Proceed to
|
LH side turn signal lights blink
|
A
|
LH side turn signal lights do not blink
|
B
|
B
|
|
|
7.
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH AND OUTER REAR VIEW MIRROR ASSEMBLY LH - COMBINATION METER ASSEMBLY)
|
(a) Disconnect the I5 combination meter assembly connector.
(b) Disconnect the L9 outer rear view mirror assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A131-6 (B)*1, A134-1 (B)*2, L9-5 (B) or I5-5 (LL) - Body ground
|
Always
|
10 kΩ or higher
|
-
*1: for LED Type Front Turn Signal Light
-
*2: for Bulb Type Front Turn Signal Light
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
8.
|
CHECK RH SIDE LIGHTS (REAR COMBINATION LIGHT ASSEMBLY RH)
|
(a) Disconnect the O103*1, O42*2 rear combination light assembly RH connector.
(b) Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the rear turn signal light blink.
HINT:
If the RH side turn signal lights blink, the rear light assembly RH is malfunctioning.
-
*1: for Sedan
-
*2: for Hatchback
Result
|
Proceed to
|
RH side turn signal lights blink
|
A
|
RH side turn signal lights do not blink
|
B
|
A |
|
REPLACE REAR COMBINATION LIGHT ASSEMBLY RH
for Hatchback: Click here
for Sedan: Click here
|
B
|
|
|
9.
|
CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY)
|
(a) Disconnect the O103*1, O42*2 combination light assembly RH connector.
(b) Disconnect the I5 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (for Sedan):
Tester Connection
|
Condition
|
Specified Condition
|
O103-3 (B) or I5-21 (TRNR) - Body ground
|
Always
|
10 kΩ or higher
|
Standard Resistance (for Hatchback):
Tester Connection
|
Condition
|
Specified Condition
|
O42-4 (B) or I5-21 (TRNR) - Body ground
|
Always
|
10 kΩ or higher
|
-
*1: for Sedan
-
*2: for Hatchback
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
10.
|
CHECK RH SIDE LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)
|
(a) Connect the O103*1, O42*2 rear combination light assembly RH connector.
(b) Connect the I5 combination meter assembly connector.
(c) Disconnect the K10 outer rear view mirror assembly RH connector.
(d) Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the side turn signal light blink.
HINT:
If the RH side turn signal lights blink, the outer rear view mirror assembly RH is malfunctioning.
-
*1: for Sedan
-
*2: for Hatchback
Result
|
Proceed to
|
RH side turn signal lights blink
|
A
|
RH side turn signal lights do not blink
|
B
|
A
|
|
|
11.
|
INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
|
Click here
12.
|
CHECK RH SIDE LIGHTS (HEADLIGHT ASSEMBLY RH)
|
(a) Connect the K10 outer rear view mirror assembly RH connector.
(b) Disconnect the A133*1, A132*2 headlight assembly RH connector.
(c) Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the headlight turn signal light blink.
HINT:
If the RH side turn signal lights blink, the headlight assembly RH is malfunctioning.
-
*1: for LED Type Front Turn Signal Light
-
*2: for Bulb Type Front Turn Signal Light
Result
|
Proceed to
|
RH side turn signal lights blink
|
A
|
RH side turn signal lights do not blink
|
B
|
B
|
|
|
13.
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH AND OUTER REAR VIEW MIRROR ASSEMBLY RH - COMBINATION METER ASSEMBLY)
|
(a) Disconnect the I5 combination meter assembly connector.
(b) Disconnect the K10 outer rear view mirror assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A133-6 (B)*1, A132-1 (B)*2, K10-5 (B) or I5-6 (LR) - Body ground
|
Always
|
10 kΩ or higher
|
-
*1: for LED Type Front Turn Signal Light
-
*2: for Bulb Type Front Turn Signal Light
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|