- Perform reset memory
- CVT oil pressure calibration
- Perform road test to allow TCM to learn
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000028H9P |
| Model Year Start: 2023 | Model: Corolla Hatchback | Prod Date Range: [11/2022 - 03/2023] |
| Title: K120 / K121 (CVT): TRANSMISSION CONTROL CABLE (for TMC Made): REMOVAL; 2023 MY Corolla Corolla Hatchback [11/2022 - 03/2023] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed, or replaced during floor shift transmission control select cable removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replacement Part or Procedure |
Necessary Procedure |
Effect/Inoperative when not Performed |
Link |
|---|---|---|---|
|
*1: w/o Smart Key System
*2: w/ Smart Key System *3: w/ Steering Lock Function |
|||
|
Replacement of ECM |
Vehicle Identification Number (VIN) registration |
MIL comes on |
|
|
Update ECU security key |
Vehicle Control History (RoB) are stored |
|
|
|
ECU communication ID registration (Immobiliser system) |
Engine start function |
|
|
|
|
|
|
|
|
Replacement of ECM*2 |
Code registration (Smart Key System (for Gasoline Model, Start Function)) |
|
|
|
Replacement of ECM*1 |
Code registration (Immobiliser system) |
|
|
|
Gas leak from exhaust system is repaired |
Inspection after repair |
|
|
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
|
Effect/Inoperative Function when Necessary Procedure not Performed |
Necessary Procedure |
Link |
|---|---|---|
|
Front Camera System |
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more. |
|
Learning completes when vehicle is operated normally
|
Effect/Inoperative Function when Necessary Procedure not Performed |
Necessary Procedure |
Link |
|---|---|---|
| *1: for Hatchback | ||
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
PROCEDURE
1. REMOVE BATTERY
Click here
![2023 - 2025 MY Corolla Corolla Hatchback [11/2022 - ]; MAINTENANCE: M20A-FKS BATTERY: REMOVAL](/t3Portal/stylegraphics/info.gif)
2. REMOVE ECM
Click here
3. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here
4. REMOVE FRONT FLOOR COVER LH
Click here
5. REMOVE FRONT FLOOR COVER RH
Click here
6. REMOVE FRONT FLOOR CENTER BRACE
Click here
7. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
Click here
8. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
|
(a) Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body. |
|
9. REMOVE CONSOLE BOX ASSEMBLY
Click here
10. REMOVE FLOOR SHIFT TRANSMISSION CONTROL SELECT CABLE
(a) Move the shift lever to N.
|
(b) Disconnect the floor shift transmission control select cable from the transmission floor shift assembly. |
|
|
(c) Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the floor shift transmission control select cable from the transmission floor shift assembly. NOTICE: Do not forcibly pull the floor shift transmission control select cable into the cabin. |
|
|
(d) While disengaging the clip as shown in the illustration, disconnect the floor shift transmission control select cable from the transmission control shaft lever together with the clip. |
|
|
(e) Remove the clip and disconnect the floor shift transmission control select cable from the No. 1 transmission control cable bracket. |
|
|
(f) Remove the nut and disconnect the floor shift transmission control select cable from the vehicle body. |
|
|
(g) Remove the 2 nuts and floor shift transmission control select cable from the vehicle body. |
|
|
|