- Poor idle, etc.
- Engine start function, etc.
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000028H2R |
| Model Year Start: 2023 | Model: Corolla | Prod Date Range: [11/2022 - ] |
| Title: 2ZR-FXE (FUEL): FUEL TANK (w/o Canister Pump Module): REMOVAL; 2023 - 2025 MY Corolla Corolla HV [11/2022 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Gas leak from exhaust system is repaired |
Inspection after repair |
|
|
CAUTION:
-
Never perform work on fuel system components near any possible ignition sources.
- Vaporized fuel could ignite, resulting in a serious accident.
-
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
- Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
-
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
|
Effect/Inoperative Function when Necessary Procedure not Performed |
Necessary Procedure |
Link |
|---|---|---|
|
Front Camera System |
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more. |
|
PROCEDURE
1. PRECAUTION
|
(a) When removing and storing the fuel tank assembly, arrange the fuel tank filler pipe assembly as shown in the illustration, and secure the fuel tank assembly using a cord or similar. NOTICE: Depending on the arrangement of the fuel tank filler pipe assembly during storage, the fuel tank filler pipe assembly and rear suspension may interfere and cause fuel leakage. |
|
2. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Click here
![2023 - 2025 MY Corolla Corolla HV [11/2022 - ]; 2ZR-FXE (FUEL): FUEL PUMP (w/o Canister Pump Module): REMOVAL](/t3Portal/stylegraphics/info.gif)
3. DRAIN FUEL
4. REMOVE REAR WHEEL
Click here
5. REMOVE REAR WHEEL HOUSE LINER LH
(a) w/ Rear Wheel House Front Plate:
Remove the rear wheel house front plate.
Click here
|
(b) w/ No. 2 Floor Under Cover: (1) Remove the 6 clips (A). (2) Turn the 4 clips (B), clip (C) and remove the No. 2 floor under cover. NOTICE: If the 5 clips are not turned when the No. 2 floor under cover is removed, the No. 2 floor under cover or stud bolt may be damaged. HINT: Do not remove the clips from the No. 2 floor under cover. |
|
|
(c) Remove the 3 clips (A), clip (B), clip (C) and rear bumper side seal LH. |
|
|
(d) w/o Rear Wheel House Front Plate: Remove the clip (A), 8 clips (B), 2 screws (C) and screw (D). |
|
|
(e) w/ Rear Wheel House Front Plate: Remove the clip (A), 8 clips (B) and 2 screws (C). |
|
|
(f) Remove the clip and rear wheel house liner LH. |
|
6. REMOVE TAIL EXHAUST PIPE ASSEMBLY
Click here
7. REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)
Click here
8. REMOVE REAR FLOOR SIDE MEMBER COVER RH (w/ Cover)
Click here
9. REMOVE FUEL TANK CAP ASSEMBLY
(a) Remove the fuel tank cap assembly from the fuel tank filler pipe assembly.
10. DISCONNECT FUEL TANK FILLER PIPE ASSEMBLY
|
(a) Remove the bolt. |
|
|
(b) Disengage the locations shown in the illustration, and disconnect the fuel tank filler pipe assembly from the vehicle body. |
|
11. REMOVE NO. 1 FUEL TANK PROTECTOR
|
(a) Remove the 4 clips and No. 1 fuel tank protector from the fuel tank assembly. |
|
12. DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
|
(a) Disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel pipe. |
|
13. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
|
(a) Disconnect the fuel tank main tube sub-assembly from the fuel pipe. Click here
|
|
14. REMOVE FUEL TANK ASSEMBLY
CAUTION:
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
|
(a) Support the fuel tank assembly using an engine lifter. HINT: Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal. |
|
|
(b) Remove the 4 bolts. |
|
(c) Lower the engine lifter to remove the fuel tank assembly.
NOTICE:
- Be careful not to drop the fuel tank assembly.
- When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
15. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
|
(a) Disengage the 3 clamps to remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly. |
|
16. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
|
(a) Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly. |
|
17. REMOVE CHARCOAL CANISTER OUTLET HOSE
|
(a) Disconnect the charcoal canister outlet hose from the fuel tank filler pipe assembly. |
|
(b) Disengage the 2 clamps to remove the charcoal canister outlet hose from the fuel tank assembly.
|
|