SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000028FYT
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [11/2022 - ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
Airbag sensor assembly	Write the VIN/Vehicle Identification Number	-
	ECU configuration	Vehicle Control History (RoB) are stored
	Update ECU security key	Vehicle Control History (RoB) are stored
	Perform "Reset Memory"* Perform "Calibration"*	DTCs are stored ABS warning light illuminates Brake system warning light (yellow indicator) illuminates Slip indicator light illuminates Electronically controlled brake system disabled or malfunctions
	Switch the specification information	-
	Zero point calibration (Occupant Classification System)	Occupant Classification System Passenger airbag ON/OFF indicator Airbag System (Front passenger side) Seat Belt Warning System (Front passenger)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Airbag sensor assembly	Write the VIN/Vehicle Identification Number	-
	ECU configuration	Vehicle Control History (RoB) are stored
	Update ECU security key	Vehicle Control History (RoB) are stored
	for G16E-GTS: ECU Data Initialization	Active Torque Split AWD System
	Perform "Reset Memory" Perform "Calibration"	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates	w/ Electric Parking Brake System w/o Electric Parking Brake System
	Switch the specification information	-
	Zero point calibration (Occupant classification system)	Occupant Classification System Passenger airbag ON/OFF indicator Airbag System (Front passenger side)	for TMC Made for TMMMS Made

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Items for which learning is completed by driving the vehicle (for HV Model)

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

Items for which learning is completed by driving the vehicle (for Gasoline Model)

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedures	Link
1: for GR Model 2: except GR Model
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.1 Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.2

Learning completes when vehicle is operated normally (for Gasoline Model)

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedures	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

NOTICE:

for HV Model

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

for Gasoline Model

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)

Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FKS: Click here

for 2ZR-FXE: Click here

for G16E-GTS: Click here

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

4. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

for G16E-GTS: Click here

except G16E-GTS: Click here

5. REMOVE FRONT NO. 1 CONSOLE BOX INSERT

for G16E-GTS: Click here

except G16E-GTS Click here

6. REMOVE AIRBAG SENSOR ASSEMBLY

(a) Check that the ignition switch (for Gasoline Model) or power switch (for HV Model) is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(c) Push down the part (A) in the direction indicated by the arrow (1) to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

*a	Lock Lever
	Release the lock (1)
	Disconnect the connector (2)

(d) Remove the 3 bolts and airbag sensor assembly.

REMOVAL

CAUTION / NOTICE / HINT

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

for G16E-GTS:

Items for which learning is completed by driving the vehicle (for HV Model)

Items for which learning is completed by driving the vehicle (for Gasoline Model)

Learning completes when vehicle is operated normally (for Gasoline Model)

Power Door Lock Control System

for HV Model

for Gasoline Model

PROCEDURE