Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000028FYQ |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: REAR SEAT SIDE AIRBAG ASSEMBLY: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat airbag assembly removal/installation are shown below.
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Items for which learning is completed by driving the vehicle (for HV Model)
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedures
|
Link
|
Front Camera System
|
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
|
|
Items for which learning is completed by driving the vehicle (for Gasoline Model)
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedures
|
Link
|
Front Camera System
|
-
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
-
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
|
|
Learning completes when vehicle is operated normally (for Gasoline Model)
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedures
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
NOTICE:
for HV Model
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
-
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))
for Gasoline Model
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
-
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
NOTICE:
After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS: Click here
for 2ZR-FXE: Click here
for G16E-GTS: Click here
CAUTION:
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
4. REMOVE REAR SEAT HEADREST ASSEMBLY (w/ Removable Headrest)
Click here
5. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY (for Hatchback RH Side)
Click here
6. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY
Click here
7. REMOVE REAR SEATBACK ASSEMBLY LH (for LH Side)
Click here
8. REMOVE REAR SEATBACK ASSEMBLY RH (for RH Side)
Click here
9. REMOVE REAR SEAT CUSHION ASSEMBLY
for HV Model: Click here
for Gasoline Model: Click here
10. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
11. REMOVE REAR DOOR SCUFF PLATE
for Sedan (for HV Model): Click here
for Sedan (for Gasoline Model): Click here
for Hatchback: Click here
12. REMOVE REAR UNDER SIDE COVER (for HV Model)
Click here
13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
HINT:
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear seat side garnish.
14. REMOVE REAR SEAT SIDE GARNISH
for Sedan: Click here
for Hatchback: Click here
15. REMOVE REAR SEAT AIRBAG ASSEMBLY
CAUTION:
When storing the rear seat airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side
|
(a) Check that the ignition switch (for Gasoline Model) or power switch (for HV Model) is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(d) Disengage the clip and separate the rear seat airbag assembly.
NOTICE:
When separating the rear seat airbag assembly, do not pull the airbag wire harness.
(e) Disconnect the airbag connector to remove the rear seat airbag assembly.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
HINT:
Refer to How to Connect or Disconnect Airbag Connector.
Click here
|