| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000028D8Q |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): VSC OFF Switch Circuit; 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [11/2022 - ] | ||
|
VSC OFF Switch Circuit |
DESCRIPTION
The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch (combination switch assembly) turns off TRAC operation, and pressing and holding this switch turns off TRAC and VSC operation. If TRAC and VSC operations are turned off, "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.
WIRING DIAGRAM
PROCEDURE
|
1. |
READ VALUE USING GTS (TRAC/VSC OFF MODE) |
(a) Connect the GTS to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Data List.
Chassis > Brake > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
TRC(TRAC)/VSC OFF Mode |
TRAC/VSC off mode |
Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC expert mode (VSC expert mode MID ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) |
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRAC off mode VSC expert mode (VSC expert mode MID ON): VSC expert mode VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
Chassis > Brake > Data List
|
Tester Display |
|---|
|
TRC(TRAC)/VSC OFF Mode |
(d) Check the indicator light and mode condition on the GTS changes according to VSC OFF switch (combination switch assembly) operation.
Standard:
|
Switch Operation |
Mode Condition Display |
Multi-information Display ("Traction Control Turned Off") |
VSC OFF Indicator Light |
|---|---|---|---|
|
Not pressed |
Normal mode (TRC(TRAC) ON/VSC ON) |
Not displayed |
Does not come on |
|
Pressing the VSC OFF switch (combination switch assembly) |
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) |
Displayed |
Does not come on |
|
Pressing and holding the VSC OFF switch (combination switch assembly) |
VSC OFF mode (TRC(TRAC) OFF/VSC OFF) |
Displayed |
Comes on |
|
Result |
Proceed to |
|---|---|
|
Indicator light and mode condition display do not change |
A |
|
Mode condition display is normal, but indicator light does not change |
B |
|
Indicator light and mode condition display are normal |
C |
| B |
|
INSPECT METER / GAUGE SYSTEM except 12.3 Inch Display: Click here
for 12.3 Inch Display: Click here
|
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
| C |
|
|
|
2. |
INSPECT VSC OFF SWITCH (COMBINATION SWITCH ASSEMBLY) |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector. OK: The connector is securely connected. |
|
(b) Disconnect the I61 VSC OFF switch (combination switch assembly) connector.
(c) Check both the connector case and the terminal for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance (w/o Drive Mode Switch Toggle Type):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
7 (+) - 5 (E) |
Switch pushed |
Below 50 Ω |
|
7 (+) - 5 (E) |
Switch not pushed |
10 kΩ or higher |
Standard Resistance (w/ Drive Mode Switch Toggle Type):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
8 (+) - 5 (E) |
Switch pushed |
Below 50 Ω |
|
8 (+) - 5 (E) |
Switch not pushed |
10 kΩ or higher |
| NG |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH (COMBINATION SWITCH ASSEMBLY)) |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the I61 VSC OFF switch (combination switch assembly) connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance (w/o Drive Mode Switch Toggle Type):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I61-7 (+) - A51-38 (CSW) |
Always |
Below 1 Ω |
|
I61-7 (+) or A51-38 (CSW) - Body ground |
Always |
10 kΩ or higher |
|
I61-5 (E) - Body ground |
1 minute or more after disconnecting the cable from the negative (-) battery terminal |
Below 1 Ω |
Standard Resistance (w/ Drive Mode Switch Toggle Type):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I61-8 (+) - A51-38 (CSW) |
Always |
Below 1 Ω |
|
I61-8 (+) or A51-38 (CSW) - Body ground |
Always |
10 kΩ or higher |
|
I61-5 (E) - Body ground |
1 minute or more after disconnecting the cable from the negative (-) battery terminal |
Below 1 Ω |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|