| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000028D8F |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): Brake Hold Operated Indicator Light Circuit; 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [11/2022 - ] | ||
|
Brake Hold Operated Indicator Light Circuit |
DESCRIPTION
The brake hold operated indicator light illuminates when the brake hold system is operating (vehicle stopped due to brake fluid pressure hold) and turns off when the brake hold system operation is finished (brake fluid pressure decreases).
The brake hold system may not operate depending on vehicle conditions even when the system is in standby mode and the brake hold standby indicator light is illuminated.
If there is a system malfunction that causes brake hold control to be prohibited, when the vehicle is under the following conditions and the brake hold switch (electric parking brake switch assembly) is pressed, the brake hold operated indicator light blinks.
-
Vehicle Conditions:
- The driver door is closed.
- The driver seat belt is fastened.
HINT:
- When the ignition switch is turned off during brake hold operation, control stops.
-
If brake hold control does not operate even when the vehicle stops, depress on the brake pedal again firmly to stop the vehicle.
If brake hold control still does not operate, confirm the conditions for brake hold control to operate.
PROCEDURE
|
1. |
PRE-CHECK |
(a) Check that the brake hold standby indicator light operates normally.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [11/2022 - ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): Brake Hold Standby Indicator Light Circuit](/t3Portal/stylegraphics/info.gif)
(b) If the brake hold operated indicator light does not illuminate even though the brake hold standby indicator light is illuminated, check that the following brake hold operation (brake fluid pressure is being maintained ) conditions are met.
- System is in operation standby state (brake hold standby indicator light is illuminated).
- Shift position is not P or R.
- Driver is depressing brake pedal and vehicle is fully stopped.
- Driver is not depressing accelerator pedal.
- Vehicle is not on steep decline.
HINT:
If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.
- Brake system
- Electric parking brake system
|
|
2. |
CHECK VEHICLE CONTROL HISTORY (RoB) (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM) |
(a) Connect the GTS to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Utility / Vehicle Control History (RoB).
(d) Using the GTS, check for Vehicle Control History (RoB).
Click here
Chassis > Brake/EPB > Utility
|
Tester Display |
|---|
|
Vehicle Control History (RoB) |
HINT:
If vehicle control history (RoB) is stored when the electronically controlled brake system and electric parking brake system are suspended and the brake hold switch (electric parking brake switch assembly) is operated with the following vehicle conditions met, the brake hold operated indicator light blinks.
- The driver door is closed.
- The driver seat belt is fastened.
|
Result |
Proceed to |
|---|---|
|
There is no vehicle control history (RoB) for when the electronically controlled brake system and electric parking brake system were suspended. |
A |
|
There is vehicle control history (RoB) for when the electronically controlled brake system and/or electric parking brake system were suspended. |
B |
| B |
|
PERFORM TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY (RoB) NOTICE: After performing troubleshooting and repair regarding vehicle control history (RoB), clear the vehicle control history (RoB). |
|
|
3. |
CHECK VEHICLE |
(a) Check the combination meter assembly.
|
Result |
Proceed to |
|---|---|
|
except 12.3 Inch Display |
A |
|
for 12.3 Inch Display |
B |
| B |
|
|
|
4. |
INSPECT COMBINATION METER ASSEMBLY |
(a) Connect the GTS to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(d) Perform the Active Test of the combination meter assembly using the GTS.
Click here
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Hold Indicator |
(e) Check the combination meter assembly.
OK:
The brake hold operated indicator light turns on or off in accordance with the GTS operation.
| OK |
|
| NG |
|
|
5. |
INSPECT COMBINATION METER ASSEMBLY |
(a) Connect the GTS to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(d) Perform the Active Test of the combination meter assembly using the GTS.
Click here
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Multi Display All (White) |
(e) Check the combination meter assembly.
OK:
The multi-information display turns on or off in accordance with GTS operation.
| OK |
|
| NG |
|
|
|