- ECM main line or connector
- Power source circuit of ECM
- ECM ground circuit
- ECM
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000028ABK |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - 03/2023] |
| Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): ECM Communication Stop Mode; 2023 MY Corolla Corolla Hatchback GR Corolla [11/2022 - 03/2023] | ||
|
ECM Communication Stop Mode |
DESCRIPTION
|
Detection Item |
Symptom |
Trouble Area |
|---|---|---|
|
ECM Communication Stop Mode |
Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS. Click here
|
|
WIRING DIAGRAM
for M20A-FKS
for G16E-GTS
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
-
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
![2023 MY Corolla Corolla Hatchback GR Corolla [11/2022 - 08/2023]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
- Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 10 minutes or more before measuring the resistance.
-
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click here
-
When disconnecting and reconnecting the battery.
HINT:
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
-
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
-
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
-
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
|
1. |
CHECK VEHICLE TYPE |
(a) Check vehicle type.
|
Result |
Proceed to |
|---|---|
|
for M20A-FKS |
A |
|
for G16E-GTS |
B |
| B |
|
|
|
2. |
CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE) |
(a) Disconnect the cable from the negative (-) battery terminal.
|
(b) Disconnect the A47 ECM connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A47-8 (CANH) - A47-18 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM) |
|
|
3. |
CHECK ECM POWER SOURCE CIRCUIT |
(a) Check the ECM power source circuit.
Click here
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
|
4. |
CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the A139 ECM connector.
|
*a |
Front view of wire harness connector (to ECM) |
- |
- |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A139-8 (CANH) - A139-18 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM) |
|
|
5. |
CHECK ECM POWER SOURCE CIRCUIT |
(a) Check the ECM power source circuit.
Click here
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
|
|