Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000289WE
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [11/2022 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: OCCUPANT CLASSIFICATION SYSTEM (for TMMMS Made): B179312; Load Sensor for Occupant Detection System Circuit Short to Battery; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]

DTC

B179312

Load Sensor for Occupant Detection System Circuit Short to Battery

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B179312

Load Sensor for Occupant Detection System Circuit Short to Battery

When the detections voltage higher than specified value before supplying power to the sensor.
  • Harness or connector
  • Airbag sensor assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART

  • After replacing the airbag sensor assembly, refer to work procedure.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - 03/2023]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2023 - 08/2023]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE 2024 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [08/2023 -        ]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE

HINT:

  • If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
  • In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(c) Check that the connectors are properly connected to the airbag sensor assembly and separate type front seat cushion spring assembly RH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY
OK

2.

CHECK CONNECTORS

(a) Disconnect the airbag sensor assembly connector.

*1

Separate Type Front Seat Cushion Spring Assembly RH

*2

Airbag Sensor Assembly

*3

Wire Harness

(b) Disconnect the separate type front seat cushion spring assembly RH connector.

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH)

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

*1

Separate Type Front Seat Cushion Spring Assembly RH

*2

Airbag Sensor Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Separate Type Front Seat Cushion Spring Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Separate Type Front Seat Cushion Spring Assembly RH (Rear Occupant Classification Sensor LH))

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

O17-24 (SVC) - Body ground

Ignition switch ON

Below 1 V

j6-1 (SVC) - Body ground

Ignition switch ON

Below 1 V

j7-1 (SVC) - Body ground

Ignition switch ON

Below 1 V
OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR