01
|
Out of FI Load Sensor Upper Limit Standard
|
When any of the following conditions is detected:
-
The sensor load value before learning is not as specified (upper limit exceeded)
-
The sensor load value after learning is not as specified (upper limit exceeded)
|
Check for the following
-
Check whether the vehicle and seat are subject to vibration or a load
-
Check front seat assembly RH installation
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the separate type front seat cushion spring assembly RH (occupant classification sensor).
|
02
|
Out of FI Load Sensor Lower Limit Standard
|
When any of the following conditions is detected:
-
The sensor load value before learning is not as specified (below lower limit)
-
The sensor load value after learning is not as specified (below lower limit)
|
Check for the following
-
Check whether the vehicle and seat are subject to vibration or a load
-
Check front seat assembly RH installation
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the separate type front seat cushion spring assembly RH (occupant classification sensor).
|
03
|
Out of RI Load Sensor Upper Limit Standard
|
When any of the following conditions is detected:
-
The sensor load value before learning is not as specified (upper limit exceeded)
-
The sensor load value after learning is not as specified (upper limit exceeded)
|
Check for the following
-
Check whether the vehicle and seat are subject to vibration or a load
-
Check front seat assembly RH installation
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the separate type front seat cushion spring assembly RH (occupant classification sensor).
|
04
|
Out of RI Load Sensor Lower Limit Standard
|
When any of the following conditions is detected:
-
The sensor load value before learning is not as specified (below lower limit)
-
The sensor load value after learning is not as specified (below lower limit)
|
Check for the following
-
Check whether the vehicle and seat are subject to vibration or a load
-
Check front seat assembly RH installation
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the separate type front seat cushion spring assembly RH (occupant classification sensor).
|
10
|
Nonvolatile Memory Storage Failure
|
When a memory malfunction caused by either of the following is detected:
-
Writing failure
-
IGR low voltage (below 8 V)
|
Check for the following
-
Check for DTC
-
Check Vehicle Control History (RoB)
-
Measure IGR terminal voltage
HINT:
If below 8 V, check the power source circuit.
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the airbag sensor assembly.
|
11
|
Zero Point Learning Timeout
|
Occupant Detection Sensor Zero Point Calibration does not complete within 2 seconds (within the specified number of seconds)
|
Check for the following
-
Clear the Vehicle Control History (RoB)
-
Check Vehicle Control History (RoB)
-
Check whether the vehicle and seat are subject to vibration or a load
-
Check front seat assembly RH installation
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the airbag sensor assembly.
|
13
|
FI Load Sensor Malfunction
|
When a load sensor malfunction is detected
|
Check for the following
-
Check for DTC
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the separate type front seat cushion spring assembly RH (occupant classification sensor).
|
14
|
RI Load Sensor Malfunction
|
When a load sensor malfunction is detected
|
Check for the following
-
Check for DTC
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the separate type front seat cushion spring assembly RH (occupant classification sensor).
|
17
|
FI LIN Communication Lost
|
When a communication malfunction with the load sensor is detected
|
Check for the following
-
Check for DTC
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, Refer to "LIN Communication Circuit"
|
18
|
RI LIN Communication Lost
|
When a communication malfunction with the load sensor is detected
|
Check for the following
-
Check for DTC
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, Refer to "LIN Communication Circuit"
|
21
|
ECU Malfunction
|
When an airbag sensor assembly malfunction is detected
|
Check for the following
-
Check for DTC
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the airbag sensor assembly.
|
22
|
IGR Voltage Malfunction
|
When IGR voltage (below 8 V or 16 V or higher) is detected
|
Check for the following
-
Check Vehicle Control History (RoB)
-
Measure IGR terminal voltage
HINT:
If below 8 V or 16 V or higher, check the power source circuit.
|
23
|
Load Unstable
|
When any of the following conditions is detected:
-
The vehicle and seat are subject to vibration or a load
-
Sensor malfunction
|
Check for the following
-
Check whether the vehicle and seat are subject to vibration or a load
-
Perform Occupant Detection Sensor Zero Point Calibration again
HINT:
If the error code is output again, replace the separate type front seat cushion spring assembly RH (occupant classification sensor).
|