| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000289VG |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [11/2022 - ] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B166A62; Right Side Restraints Sensor 5 / Left Side Restraints Sensor 5 Signal Compare Failure; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] | ||
|
DTC |
B166A62 |
Right Side Restraints Sensor 5 / Left Side Restraints Sensor 5 Signal Compare Failure |
DESCRIPTION
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Warning Indicate |
DTC Output from |
Priority |
Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
|
B166A62 |
Right Side Restraints Sensor 5 / Left Side Restraints Sensor 5 Signal Compare Failure |
The difference between the pressure detected by the side airbag pressure sensor LH and the side airbag pressure sensor RH exceeds a certain value a certain number of times. |
|
Comes on |
SRS Airbag |
A |
Does not apply to test/check mode |
CAUTION / NOTICE / HINT
NOTICE:
-
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
-
After replacing the airbag sensor assembly, refer to work procedure.
Click here
PROCEDURE
|
1. |
CHECK DTC |
(a) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
No DTCs in the table below are output |
A |
|
Any of the DTCs in the table below are output |
B |
|
Malfunction Content |
System |
Relevant DTC |
|
|---|---|---|---|
|
Side collision sensor circuit (bus 1) malfunction |
Airbag system |
B009B64 |
Left Side Restraints Sensor 5 Signal Plausibility Failure |
|
B009B83 |
Left Side Restraints Sensor 5 Value of Signal Protection Calculation Incorrect |
||
|
B009B84 |
Left Side Restraints Sensor 5 Signal Below Allowable Range |
||
|
B009B85 |
Left Side Restraints Sensor 5 Signal Above Allowable Range |
||
|
B009B87 |
Left Side Restraints Sensor 5 Missing Message |
||
|
B009B96 |
Left Side Restraints Sensor 5 Component Internal Failure |
||
|
B009E64 |
Right Side Restraints Sensor 5 Signal Plausibility Failure |
||
|
B009E83 |
Right Side Restraints Sensor 5 Value of Signal Protection Calculation Incorrect |
||
|
B009E84 |
Right Side Restraints Sensor 5 Signal Below Allowable Range |
||
|
B009E85 |
Right Side Restraints Sensor 5 Signal Above Allowable Range |
||
|
B009E87 |
Right Side Restraints Sensor 5 Missing Message |
||
|
B009E96 |
Right Side Restraints Sensor 5 Component Internal Failure |
||
HINT:
If DTCs in the table above are output, troubleshoot those DTCs first.
| B |
|
|
|
2. |
CLEAR DTC |
Pre-procedure1
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
(c) Replace the side airbag pressure sensor RH with a new one or known good one.
HINT:
Click here
HINT:
- When using a new part, since the side airbag pressure sensor LH and RH have the same part number, prepare either one.
- Use the prepared side airbag pressure sensor to check the side airbag pressure sensor LH as well.
(d) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
(e) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
Post-procedure1
(g) Turn the ignition switch off.
|
|
3. |
CHECK SIDE AIRBAG PRESSURE SENSOR RH |
Pre-procedure1
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(b) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
B166A62 is output |
A |
|
B166A62 is not output |
B |
HINT:
Codes other than DTC B166A62 may be output at this time, but they are not related to this check.
Post-procedure1
(c) Turn the ignition switch off.
(d) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
(e) Return the side airbag pressure sensor RH that was installed for testing to its original location.
| B |
|
|
|
4. |
CLEAR DTC |
Pre-procedure1
(a) Replace the side airbag pressure sensor LH with a new one or known good one.
HINT:
Click here
HINT:
- When using a new part, since the side airbag pressure sensor LH and RH have the same part number, prepare either one.
- Use the prepared side airbag pressure sensor to check the side airbag pressure sensor RH as well.
(b) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(d) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
Post-procedure1
(e) Turn the ignition switch off.
|
|
5. |
CHECK SIDE AIRBAG PRESSURE SENSOR LH |
Pre-procedure1
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(b) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
B166A62 is output |
A |
|
B166A62 is not output |
B |
HINT:
Codes other than DTC B166A62 may be output at this time, but they are not related to this check.
Post-procedure1
(c) Turn the ignition switch off.
(d) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
(e) Return the side airbag pressure sensor LH that was installed for testing to its original location.
| A |
|
| B |
|
|
|