Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000289VD
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [11/2022 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B00D512; Restraint System Passenger Disable Indicator Circuit Short to Battery; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]

DTC

B00D512

Restraint System Passenger Disable Indicator Circuit Short to Battery

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

DTC Output from

Priority

Test Mode / Check Mode

B00D512

Restraint System Passenger Disable Indicator Circuit Short to Battery
  • The airbag sensor assembly detects a short circuit +B signal in the passenger airbag ON/OFF indicator "OFF" circuit when the airbag sensor assembly sends an "ON" request signal to the "OFF" indicator in the passenger airbag ON/OFF indicator.
  • Passenger airbag ON/OFF indicator malfunction
  • Airbag sensor assembly malfunction
  • Harness or connector
  • Passenger airbag ON/OFF indicator (map light assembly)
  • Airbag sensor assembly

Comes on

SRS Airbag

A

Does not apply to test/check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART

  • After replacing the airbag sensor assembly, refer to work procedure.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - 03/2023]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2023 - 08/2023]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE 2024 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [08/2023 -        ]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag sensor assembly and map light assembly.

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY
OK

2.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag sensor assembly connector.

*1

Map Light Assembly

*2

Airbag Sensor Assembly

*3

Wire Harness

(b) Disconnect the map light assembly connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I47-34 (P-AB) or T6-18 (P-AB) - Body ground

Ignition switch ON

Below 1 V

Result:

Proceed to

OK

NG

*1

Map Light Assembly

*2

Airbag Sensor Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Map Light Assembly)

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

Post-procedure1

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

4.

CHECK PASSENGER AIRBAG ON/OFF INDICATOR

Pre-procedure1

(a) Connect the map light assembly connector.

*1

Map Light Assembly

*2

Airbag Sensor Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

(b) Using a service wire, connect terminal 34 (P-AB) of connector B and body ground.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON.

Procedure1

(e) Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator "OFF" come on.

Post-procedure1

(f) Turn the ignition switch off.

(g) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(h) Disconnect the service wire from connector B.

OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY