Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000289V5 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [11/2022 -
] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B009E87; Right Side Restraints Sensor 5 Missing Message; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 - ] |
DTC
|
B009E87
|
Right Side Restraints Sensor 5 Missing Message
|
DESCRIPTION
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Warning Indicate
|
DTC Output from
|
Priority
|
Test Mode / Check Mode
|
B009E87
|
Right Side Restraints Sensor 5 Missing Message
|
-
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the side collision sensor RH circuit (bus 1) for 2 seconds.
-
Side airbag pressure sensor RH malfunction
-
Airbag sensor assembly malfunction
|
-
Harness or connector
-
Side airbag pressure sensor RH
-
Airbag sensor assembly
|
Comes on
|
SRS Airbag
|
A
|
Does not apply to test/check mode
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
PROCEDURE
1.
|
CHECK CONNECTION OF CONNECTORS
|
Pre-procedure1
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
(c) Check that the connectors are properly connected to the airbag sensor assembly and side airbag pressure sensor RH.
OK:
The connectors are properly connected.
Post-procedure1
(d) None
NG |
|
CONNECT CONNECTORS PROPERLY
|
OK
|
|
|
Pre-procedure1
(a) Disconnect the airbag sensor assembly connector.
|
|
*1
|
Side Airbag Pressure Sensor RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Disconnect the side airbag pressure sensor RH connector.
Procedure1
(c) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
Post-procedure1
(d) None
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
K7-2 (BDR+) - K7-1 (BDR-)
|
Always
|
1 MΩ or higher
|
|
|
*1
|
Side Airbag Pressure Sensor RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
*a
|
Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
|
|
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)
|
Pre-procedure1
(a) Using a service wire, connect terminals 26 (BBR+) and 25 (BBR-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
|
|
*1
|
Side Airbag Pressure Sensor RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
*4
|
Service Wire
|
*a
|
Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
|
*b
|
Front view of wire harness connector
(to Airbag Sensor Assembly)
|
|
|
Procedure1
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
K7-2 (BDR+) - K7-1 (BDR-)
|
Always
|
Below 1 Ω
|
Post-procedure1
(c) Disconnect the service wire from connector B.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
K7-2 (BDR+) - Body ground
|
Always
|
1 MΩ or higher
|
K7-1 (BDR-) - Body ground
|
Always
|
1 MΩ or higher
|
|
|
*1
|
Side Airbag Pressure Sensor RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
*a
|
Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
|
|
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
6.
|
CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)
|
Pre-procedure1
(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
(b) Turn the ignition switch to ON.
Procedure1
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
K7-2 (BDR+) - Body ground
|
Ignition switch ON
|
Below 1 V
|
K7-1 (BDR-) - Body ground
|
Ignition switch ON
|
Below 1 V
|
Result:
|
|
*1
|
Side Airbag Pressure Sensor RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
*a
|
Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
|
|
|
Post-procedure1
(d) Turn the ignition switch off.
(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
Pre-procedure1
(a) Connect the airbag sensor assembly connector.
|
|
*1
|
Side Airbag Pressure Sensor LH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Interchange the side airbag pressure sensor RH with LH and connect the connectors to them.
(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
(d) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
Post-procedure1
(f) Turn the ignition switch off.
NEXT
|
|
|
8.
|
CHECK SIDE AIRBAG PRESSURE SENSOR RH
|
Pre-procedure1
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(b) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
Result
|
Proceed to
|
B009E87 is output
|
A
|
B009B87 is output
|
B
|
B009B87 and B009E87 are not output
|
C
|
HINT:
Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.
Post-procedure1
(c) Turn the ignition switch off.
(d) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
(e) Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors to them.
|