Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000027EK5 |
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [09/2022 -
] |
Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: P060E49; Internal Control Module Throttle Position Performance Internal Electronic Failure; 2023 - 2025 MY Corolla Corolla Hatchback [09/2022 - ] |
DTC
|
P060E49
|
Internal Control Module Throttle Position Performance Internal Electronic Failure
|
MONITOR DESCRIPTION
The ECM monitors the signals received from the No. 1 throttle position sensor. As the ECM monitors the VTA1 signal of the No. 1 throttle position sensor, if these signals do not correlate, a DTC will be stored.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P060E49
|
Internal Control Module Throttle Position Performance Internal Electronic Failure
|
Either of the following conditions is met (1 trip detection logic):
-
ECM main CPU malfunction.
-
ECM sub CPU malfunction.
|
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P060E
-
DTC for Mexico Models: Applies
|
MONITOR STRATEGY
Related DTCs
|
P060E: Internal control module throttle position performance
|
Required Sensors/Components (Main)
|
ECM
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
1 second
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
TYPICAL MALFUNCTION THRESHOLDS
Difference of main throttle position and sub throttle position
|
0.3 V or higher
|
CONFIRMATION DRIVING PATTERN
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the Techstream off.
-
Turn the ignition switch off.
-
Disconnect the Techstream.
-
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
-
Connect the cable to the negative (-) battery terminal.
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Wait 16 seconds or more [A].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P060E49.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the ignition switch off.
NEXT
|
|
|
2.
|
READ OUTPUT DTC (DTC P060E49)
|
(a) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(b) Connect the cable to the negative (-) battery terminal.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Wait 16 seconds or more.
(g) Enter the following menus: Powertrain / Engine / Trouble Codes.
(h) Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTC P060E49 is output
|
B
|
|